I have HSRP on the MLS on given packet tracer file. I have inter VLAN communication and dynamic routing with OSPF in the routers. I want to ping the core router with the PC and aso keep the HSRP configuration intact. Also have redundancy in the distr...
Forum Posts
Resolved! Cisco 2901 GRE Tunnel packet drops
I have two Cisco 2901 routers with simple GRE tunnel between them (no IPSec, etc). Router A:interface Tunnel3ip address 10.10.253.9 255.255.255.252keepalive 3 3tunnel source <Router A IP>tunnel destination <Router B IP> Router B:interface Tunnel3ip a...
Hi All, I have a doubt regarding the BGP TTL security feature. Cisco docs state that enabling ttl security for eBGP sessions has no effect on the outgoing IP packets but at the same time they also mention that the feature needs to be enabled on both ...
Resolved! PRI error message (RAI detected)
Dear Friends,I am getting the below log messages from one of my routers Nov 12 17:53:19.841 INT: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0:15, changed state to upNov 12 17:53:20.133 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, change...
Hi All, I need your help/suggestions in one of the issue with our BGP Multihoming environment. We have 2 ISP's and 2 Router's and we have configure BGP with our owned /24 Public IP with AS number with IBGP over HSRP for failover. Now the issue ...
Resolved! ospf over te tunnel
hellothere is a simple topology TE tunnels 10 and 14 are build to betwean IOU 10 and IOU14 interface Tunnel10ip unnumbered Loopback0tunnel mode mpls traffic-engtunnel destination 14.14.14.14tunnel mpls traffic-eng forwarding-adjacencytunnel mpls traf...
Hi I need help with this question. I am not understanding this question.
Resolved! EIGRP Topology Table
In the above scenario, I am using EIGRP to advertise routes between all the routers. When I execute show ip eigrp topology all-links on Router2 I get the following output:In the above output to reach the 192.168.1.0 network, it can go through 192.1...
Hi community, I will describe briefly my situation, I have an RV320 that we will like to upgrade to an RV340. This device is use mainly as our gateway. The device has 2 connection only, WAN port is connected to our ISP provider and LAN 1 is connec...
The peering LAN I'm trying to join the route-server for isn't adding routes to my router. They can see they're being advertised but I don't see them. I do however see something call "MALFORM treat as withdraw" could this be something to do with why I...
Resolved! MPLS VPN Traceroute
I have started noticing that the MPLS VPN exit nodes respond to traceroute with the VRF address, and not the ingress address as I typically expect. From web searches I can find people mentioning this in passing. Does anyone know where this behavior i...
Hi, I'm trying to figure out how to block ports and secure my older router that doesn't have SSL, crypto, ip inspect and I'm sure I'm missing a few other things. I added these to my my config file but I think it might have worked too well because my ...
I can make outbound calls but I don't receive inbound calls Here is a copy of my debug voice ccapi all and debug ccsip and run config debug voice ccapi allPSTN#*Nov 7 16:09:22.583: //-1/xxxxxxxxxxxx/CCAPI/cc_get_call_entry: CALL_ERROR_INFORMATIONAL; ...
I'm trying to enable SSH and secret but I seem to be missing some commands. I set the domain-name to see if that would enable it but still no go.I don't seem to have the crypto command available.The secret command isn't available when I try to create...
hi,i have posted below current configuration of my router. i'm getting internet inside the router but not getting in interface g0/1 which is connected to my switch. i can ping to google from command,but not to the devices connected to g0/1. And my DC...
