Hi All, I am having trouble with equal cost load balancing. I am trying to ping host with IP 10.0.10.11 Below are the routers that I am trying to loadbalance. But almost all off traffic is going out Ethernet0/1 only even though they are with equa...
Forum Posts
I referred BGP path selection algorithm from below link https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13753-25.html Can someone help to understand why Step #10 is only for external peers? Why is this rule not applicable ...
I have a config that I am trying to bring up, and in my mind it should work, but perhaps I am missing something. The idea is that one end of the link is a layer 3 interface on a router. The other end is a switchport trunk, on a vlan with an IP inte...
I currently have SDWan deployed in my environment, sitting behind the edge router(s) and it works great! Aggregation, fault tolerant, optimization,etc. However, it cannot forward inbound IPSec traffic to my SSLVPN appliance. Can I route 1of my exte...
Hello, I have Cisco 887v router with C800 Software (C800-universalK9-M) Version 15.3. My Scenario i have a ISP-1 with cable modem another ISP-2 with static WAN route. I want ISP-1 for IPsec VPN and ISP-2 for default internet. PLEASE HELP ME...how ...
I have just installed a CSR into Amazon AWS and have a query on routing between VPCs. There is a Public VPC with the CSR Outside interface in and a private VPC with a test server. The CSR is fully integrated into our private DMVPN and that side see...
I have a GRE over IPSec tunnel that gets high bandwidth utilization every 2-3 days and stays like that for 2-3 days. I look at the traffic using netflow on the 2811 router and 95% of the packets in and out are either GRE or IPSec. I only have two t...
Resolved! 2 Wan 2 Router IPSLA PBR
Hello, i have 2 router 4321 and 2 ISP, R1 have ISP1 R2 have ISP2 how i configure failover for this setup not just link but device failover. thank you
Resolved! Cisco 2621XM Router IOS Booting Issue
Hi All I was wondering if you can help me out, I have loaded ios c2600-ipbasek9-mz.124-25a.bin on the router, for some reason it boots twice as you can see details below, it says %SYS-6-READ_BOOTFILE_FAIL: flash:c2600-j1s3-mz.123-26.bin File boot fai...
I am able to get an ipv6 /64 address from Xfinity with no problem however I have multiple subnets I need to cover with ipv6 so I'll need a /60 or lower. How do you specify the DHCP-PD request for a /60 in the RV340 so that I can break up into a mult...
ISR 4451 support ATM or not ?
Resolved! OSPF Network Advertisment
Why when I advertise a network 192.168.0.0 with mask 255.255.254.0 it will get advertised as 192.168.0.0/24 and 192.168.1.0/24 on neighbor routers in a single area? Is there anyway this can be summarized in in a single area in OSPF?
Hello, I have an exisiting Firewall that I do not want to have as a VPN connection. Rather I would like to forward the VPN ports to make Anyconnect and S2S possible to my ASA 5510 on the inside LAN. The big reason for this is the interface limitati...
Hi Friends. in our network we configure DMVPN Hub and Spokes tunnel. in hub all traffic is on tunnel 1 . We want to send some traffic on tunnel 2. when I use the tunnel address of the spoke as the next hop, it dose not work. also I set the physical i...
Hello guys Any interactions between maximum-path and BGP PIC ,as both deal WITH multiple path thanks all
