Hello freinds What Tech shall i use to connect 3 Dispersed DCs? Application mobility requirement 1. H-VPLS 2. OTV 3. VXLAN EVPN 4. PBB EVPN pls Adivise on the Pros and Cons for each tech , i m really confused
Forum Posts
Hello! We have cisco 1921 router with the 4G LTE EHWIC card. We just copied working config from the old cisco 881 router with the 3G HSPA card and it doesn`t connect to ISP network. Error is: Inactivity Reason = Activation rejected by GGSNAlso we c...
What are the Pros and Cons of the Catalyst 9000 series?
Resolved! DMVPN - EIGRP Neighbors
Hi,I run a DMVPN solution in Dual hub mode. I use EIGRP as a routing protocol between the HUb and Spokes. I know that gre is pain most of the times but we have to live with that. Although I had EIGRP spoke neighborsstable for 8-9 weeks and someothers...
Why are loopbacks advertised as /32 host routes in OSPF?thanks!!!
Resolved! LAN static routing issue
I'm having a weird issue on a Catalyst 3560 where I have routed a subnet to a firewall but when you do a trace route it's hitting a different device. What would supersede a static route?
Current setup: A) Only one routing protocol is in use: OSPF 100, area 0 B) There are three "categories" of static routes on the router. 1) The first set is defined by a route map and redistributed into OSPF 100 via the redistribute static via route m...
I have attached a diagram of my connection. What I want to do is to use router A ip address to router B. Router A is located remotely that no one can handle it onsite. Im just doing remote connection to both routers. How I can use router A ip adr to ...
HiWhy is not possible to use management VRF for ERSPAN. I wanted to have erspan for port e1/48 from management IP 172.20.10.4 to 172.10.10.229. But it is not possible from vrf managment. Does anyone has any explanation on this ! dc2-sw02(config-erspa...
Hello can someone help me with my case? So someboody knew pgpool? i have 2 db server running pgpool, each db server has virtual db that act as gateway so basically this method is like HSRP. The problem is another server which need access to db run in...
Resolved! c881 PBR NAT
Hello, Got a task to NAT some traffic through remote c881. IPsec between devices works fine. sh run Building configuration... Current configuration : 5824 bytes ! ! Last configuration change at 17:22:39 UTC Thu Sep 6 2018 by admin ! version...
We set up a new point to point GRE tunnel between R1 and R2 running OSPFv3 and IPv6. This was a second tunnel on R1 that mirrored the other GRE tunnel. Now, although we were able to ping each other's source interfaces, ping FF02::5 and had PIM nei...
I need design assistance with bgp & ospf. 1. site-2 should use green link as primary to reach site-1 and red link as back to reach site-1.2. site-3 should use its green link as primary to reach site-1.3. site-2 and site-3 use their directly connect...
Hi, I noticed that when had I two sites request a 13 Mb video multicast stream from a third site via mGRE NHRP, the third site has to send two streams, thus over utilizing the 20Mb circuit and causing QoS policy drops. Does this sound right? The ...
Hello guys, I need some help with this set up. I'm trying to browse the internet from the client-PC and server. Here is my config. Please see the pic for the physical layout. I have a Layer 3 switch with multiple VLANS. VLAN 70: ip address:...
