HI All, I need to configure internet redundancy and need to be integrated with HSRP of my network. I am using 4331 ISR routers. The problem is I am using ipbase license only on these routers. so I need to find an alternative way for internet failov...
Forum Posts
Dear, I want to replace my 2801 and 2811 routers with ISR4331. the problem is that all ISR4000 Series having just 3 NIM to install NIM modules. but i need 4 nim to place the 4 NIM modules on it. my modules on 2801,2811 is WIC-1T, WIC-1SHDSL, 4ESW, E1...
Hello Colleagues, this is our setup (of cause a bit cleaned up): we configured a Hub and spoke DMVPN with MPLS, OSPF and BGP. R6-R5(WAN/Tun1) forms a DMVPN and R8-R5(LAN/Tun2) forms a second DMVPN. DMVPN comes up and we are able to ping each rou...
I have a VPN Setup from one location to another. location a & location bwhen Location b initiates the connection it all works When location a initiates the connection, it stops at mm_wait_MSG6, if i then run the following show crypto isakmp sa detai...
Hello Community, I have been searching around this evening for a good DMVPN Phase-3 Hierarchical DMVPN network design that has a central hub, regional hubs, and regional spokes. Most of the examples I found did not suit my needs so I decided to la...
I have an ASA 5508-X and a broadband cable modem. Used the next available public IP from the cable carrier’s /29 block for the firewall, set the route and everything worked fine, pings inbound and outbound, etc. Problem starts when we added the Vel...
Resolved! Layer 2 ( Switch) and fragmentation
Hi everybody, My curiosity again kicked in. Router f1/1----------f1Swf2------REST OF NETWORK Above router and SW are IOS based, SW is layer 2. Router: int f1/1 mtu 1530 ( router is IOS based, so mtu 1530 represents the L3 payload for layer 2) ip mtu...
Hello! :) I have Cisco RV345P Router and I Purchased two Wap361 Cisco access points. if I connect the two access points to the poe ports of my router, everything works! the wap361 access point has a POE out port, so I would like to chain one acce...
Resolved! DNS doctoring ASA 5505
Hi, I'm having some troubles getting the following configuration to work: Firewall: ASA 5505. Synology DiskStation NAS. Forwarded the necessary ports to reach it from the outside, works well. Static IP (external), subdomains configured with A rec...
Hello, I've been looking for documentation regarding how to externally backup a configuration file for an RV340. I've found answers related to other RV models. It seems that this model doesn't have the section to save the configuration file via GUI....
We have a network as in the attached image, There is a connection to internet having address space 123.45.67.0/27 and with router interface connected to internet is 123.45.67.1/27 and there is a static route out to internet. Now, we want to conne...
I have preempt configured on both HSRP configs for lets say int vlan 100. Both switches are in a VPC domain and switch1 is the higher priority with 105. Tracking of interface to routers 1 and 2 is configured on both switches. Is it best practice to h...
I am trying to troubleshoot a problem where a specific multicast group seems to have been pushed to sites that shouldn't necessarily have needed that group. The size of the stream for that group took down these sites because they didn't have enough b...
I have x2 circuits provided by my ISPI'm trying to migrate from the old to the newThe process keeps failing, with the BGP seeminly bouncing after around 2 minutesThis is the debug ip bgp at the time of connection to the new (problematic) circuit00943...
Hello, We are configuring L2VPN between N7Ks and cisco ACI. I have just realised that the following command does not exist under BGP af section: router bgp 5 neighbor 10.1.1.1 address-family l2vpn evpn l2vpn evpn import stitching-rt re...
