R1>sh ip bgp 0.0.0.0 0.0.0.0BGP routing table entry for 0.0.0.0/0, version 159313Paths: (3 available, best #1, table Default-IP-Routing-Table)Multipath: eBGP Advertised to peer-groups: External Internal Local 155.195.1.1 from 0.0.0.0 (155.19...
Hi everyone, Our Cisco 7600 router is showing a very high CPU on module 9, the process responsible for that is OBFL MSG bootdis, remote command on the module show the following: CPU utilization for five seconds: 100%/0%; one minute: 99%; five minut...
Hi, i have configured two wlan controllers model 8540 for SSO, but when the redundancy started, i have losed the connection on the management interface's primary controller via HTTPS. I can connect only via SSH or serial port. Anyone can help me?
I'm not able to assign an autonomous system number to the address-family ipv4. the command is not in my ios version. what am I missing to allow the networks to propagate across the autonomous system and the vrf? config Building configuration...!!vers...
Hi! If anyone can guide me!! I have the following scenario: IP: A.A.A.A |SERVER|------------|ASA 5506X|<------IPSEC------->|ASAXXXX|-------------|SERVER| IP: B.B.B.B The vpn ipsec specifications : Left peer (asa5506x) ip: X.X.X.X domain encrypti...
Hello, maybe any of you experts can help me with the attached Microsoft Network Monitor capture files. The PPP connection between two GSM modems (Windows 7 to Windows 7 "server") is working fine. Another connection (Device-in-field to Windows 7 "serv...
Dear All, I have one customer there are experiencing high latency from their LAN. When I tried extended ping from the router the latency was 124ms to 144ms. When the customer is pinging from the LAN the latency is 260ms. We the customer disconnected...
What is the difference between Flash memory,NVRAM in the router.
how to put cisco 1921/k9 router in rommon mode? I configured username & password on CISCO1921/K9 router and write it in memory but after that it is not taking a password which I defined. how to access router without password?
Hello, i have a problem enable policy based routing on 3560. I read lots of articles, but evidently, i missed something. I would like to know, what everything is needed to enable PBR on 3560. Here are my steps: 1. I set sdm prefer routing, reloaded ...
Hello I have a cisco 6509: NAME: "WS-C6509-NEB-A", DESCR: "Cisco Systems Catalyst 6500 9-slot Chassis System" Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXJ3, RELEASE SOFTWARE (fc1)Technical Support: http...
Hi every one, I have 2 switch SG500-28 with stackable, So when i unplugged stackable cable and do the same with the wan cable, this switch not working and i can not do any thing with it. I reboot this device and have no logs for last action. I am usi...
Hi Friends,Need your inputs on attached two design options. Which one is better and is there any kind of issue with second scenario (Diag2)?We have basically multiple sites which will connect to two MPLS service providers in any to any communication....
Hello all, I have a bit of a challenge here and I would like to get help from any one here. I am configuring a cisco 2900 router and after I have finished, I can ping the internet, the gateway and dns serevr given to me by my ISP from the router. H...
Hello, We currently have a Cisco 1941 at one of our branch offices and it is currently being used to route between a metro Ethernet connection to our main buildings and the branches local subnet. We would like to get an internet connection at the b...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-14-2025 01:24 AM | ||
| 05-13-2025 03:49 AM | ||
| 05-12-2025 03:28 PM | ||
| 05-09-2025 02:25 PM | ||
| 05-05-2025 11:47 PM |
| User | Count |
|---|---|
| 14 | |
| 8 | |
| 6 | |
| 5 | |
| 4 |
