Is it the router that connects 2 different areas or router which has one interface in area 0(backbone area) and another interface in any other area. Thank You ravi
Is it the router that connects 2 different areas or router which has one interface in area 0(backbone area) and another interface in any other area. Thank You ravi
Hey everyone Im a novice when it comes to Cisco routers. Have a 2901 in house now, and trying to get it to route between the two main interfaces. But no luck! Routing is between the 10.16.108.x and the 32.54.20.x network. The "ip routing" command ha...
Hi, Is there a Way to make port Fowarding following the Active Wan Interface ? On this case the port Fowarding only work when active interface is GigabitEthernet0/0 Bureau3616(config)# ip nat inside source static tcp 192.168.2.xxx 3389 interface Gi...
Hi Can you see the below. Why highlighted port number is different with Eth4/23 when using command show interface brif? Thank you Eth4/22 -- eth routed down Administratively down auto(D) --Eth4/23 -- eth routed down Administratively down auto(D) --E...
Hi, I tried the following command, It's working just in one way, if WAN-1 Fail on interface Fastethernet 4 the default route switch to the WAN-2 on integrated 3G interface Called Dialer 1. But the problem Is, when the WAN-1 goes back on, the Router...
Hi , i am planning to buy cisco 7606 router with 720 3CXL GE switch processor and SIP 400 module need to know will it support PPPOE or any additional module will be required . we need to have 3000 concurrent PPPOE session . please some one advise s...
Hi All, Hope you guys can help with my problem. Scenario: We want to have a site to site IPSEC VPN connection with our hosting service and also have individual client IPSEC connections to the same host but to a different network within it. Solutio...
hi, I have basic straightforward l2tp/xconenct configuration for transfering L2 traffic through my L3 network. Problem I have is that traffic exiting tunnel is out of order (wireshark says so, traffic is captured witm embended monitor capture ASR se...
Good Day, Please advise what versions of ios are compatible with 2811 and 2851 routers and if they support netflow. Thank you.
After CSCtr26978 : PfR Simplification - Phase 1 -1, effective with Cisco IOS Releases 15.2(1)S, 15.2(3)T, and Cisco IOS XE Release 3.5S, the set mode select-exit command and the best and good keywords were removed. With CSCtr26978, the default behavi...
I have two internet links.I configure port forwarding for these two internet link into my internal server.After i configure, port forwarding only work on first ISP1. It doesn't work on ISP2 and i try to ping ISP2 link but it requests timeout.If i shu...
Hi, Can anyone tell me how many GRE tunnels the 3650 and 3850 switches support (I understand GRE is supported on the new denali IOS)? Kind regards, Dave
I have a router, R254 with bad routes so my only option is to manage it from a subnet that it's on. I have another router in front of it R1 and I would like to setup NAT on that router to nat specific traffic to R254 so that it can respond. R1 Fa0/...
My RV32O is stuck in Connected inactive on Wan1 and cant connect to the internet? It worked fine last week but now its not. It connects directly to a BT openreach ISDN connection which is working fine, but the connection through the router is not rea...
hi, can i config redundancy with sup32-ge-3b and sup720-10g on cisco 6509 switch ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-16-2025 11:52 AM | ||
10-15-2025 06:33 PM | ||
10-15-2025 04:37 PM | ||
10-15-2025 12:35 PM | ||
10-15-2025 11:31 AM |
User | Count |
---|---|
5 | |
1 | |
1 | |
1 | |
1 |