Is zero touch deployment with usbflash, as described in this document, supported in the 15.4(x)M releases.I got it working with a C887VA-K9 running 15.4(1)T1 but it doesn't seem to work on a 887VAG-4G-GA-K9 running 15.4(3)M1
Dear all,I am facing some problem, I am using a /29 netmask network. I am using one ip for my office and another one ip for research purpose. But I want to use my research purpose ip in another router, but how it is possible i don't understand. Pls h...
Howdy folks, It has been some time since iv worked with a DWDM and one question has been hunting me abit. I was wondering: i currenlty have the following topology: (Switch) >> (ASR) >> (DWDM) >> (PE). Do i need to use a special SFP between the ASR an...
We are intermittently getting the below error message in Cisco7609 Router.%SIBYTE-CFC8-3-SB_UNINITIALIZED_INT: Uninitialized interrupt 0x0100000000000000%SIBYTE-CFC8-3-SB_UNINITIALIZED_INT: Uninitialized interrupt 0x0100000000000000Kindly help to und...
Hi Guys, Im hoping for some assistance.We own a small building rented out as managed office space. As part of this we have a 1Gb internet feed which we then distribute throughout the building. With each customer / office having their own managed fi...
Hello,I need to adjust the TCAM memory allocation on a Catalyst 6500 in VSS mode. The two supervisors are VS-S720-10G and the IOS is the version 15.1(2)SY4a.From what I understand, after giving the command "mls cef maximum-routes ip xxx" is necessary...
Hi Guys,Can we do this? can we send multiple show commands together in the CLI? something like this#show ip int br , show cdp nei#(out put of show ip int br)#(out put of show cdp nei)
Hi,I have a 877VAM router. Everything works ok until the reload, the router comes up but it does not connect to the internet. The only way i found it works is to ssh in, shut down dialer1, remove it, create it again, and past the same exact configura...
Hello everyone, I hava acase where I hav TCP dump ans retransmition from a client Vpn l2l and Server Domino.I have read about that the problems maybe the tcp window and my mtu also Bandwuth. here my cap of client and Server.And the flag DF is set Any...
Hi, I have purchased an 887VAG+7-K9 router but it has the NPE (no payload encryption) IOS image and licenses. Is it possible to change this to the standard K9 IOS and license? How can I do this?
Is there a way to insert a pause to wait for keyboard input when pasting a series of commands? For example I would like to paste this from a text file: Router(config)#Interface Gigabit0/1Router(config)#shutdown<pause and wait for a tap on the keyboar...
When I dir all, some 6504 shown up both disk0: and sup-bootdisk:, some shown just one of them only, even have samiliar module WS-SUP720-3B or VS-S720-10G, could help to explain the reason and what's different between disk0 and sup-bootdisk? and comma...
Hello,today I found 2 our routers without routing command, "ip route" and "router eigrp" are delete from running-config, meanwhile they are inside startup-config, when I try add again them, routers tell me i can't because disable routing, so I add "i...
Hello,Is there a command, which one can use to view the current wifi password for a wireless network from a cisco router. e.g a 1900 series router..?EDITAlso what is the command to CHANGE a wireless network password from a router such as cisco 1900 s...
The following error message generating on cisco 7206 vxr router and some time channelized stm 1 port also down. Plz help me to resolve issue Jul 23 15:14:22.777: %AAA-3-ACCT_LOW_MEM_UID_FAIL: AAA unable to create UID for incoming calls due to insuf...
