Routing

Hi all,I hope that someone can help me with a problem I seem to have with my cisco config and NAT.Basically I have 6 valid public IP addresses. I have assigned the first IP to the external interface of router. I have created an IP pool and assigned t...

Hi all,I am experiencing an issue where my Cisco 877 router's ATM interface keeps restarting due to dhcp lease timeout from my ISP every hour. I resolved this issue by applying an inbound ACL permitting DHCP packets on the ATM interface.But... The on...

Hi,We have a 2811 router and we are to connect an ADSL service to its Fast Ethernet port using PPPoE. Carrier already supplied username and password but I'm having a hard time to make it work. I'm not sure if the PPPoE configuration of the carrier is...

Hi Everyone,If you have 2 POPs, both with ME3600X's(with ADVANCED METRO IP ACCESS) - Can you create a VFI/VPLS VPN (eg. CUSTA) on both ME3600's if the "interpop" link goes via 7200's(That dont support VPLS, but would have MPLS enabled on the Interpop...

Dear experts. I am using cisco 2821 for internet router. i have two ISP with IP 10.0.1.0/29 and 10.0.2.0/29. ISP 1 is configured as follows for accessing my internal server 172.29.1.5 with nating to 10.0.1.5:interface GigabitEthernet0/0 ip address 10...

With Cisco Designated VIP Peter Palúch Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about about how to plan, design, implement, and troubleshoot IPv6 routing protocols in your n...

To All,I am now using my 837 Router on my new Server and I have only made one change to the Global configuation mode, please veiw the input below:ip dhcp pool DLSRnetwork 10.10.10.1 255.255.255.0default-router 10.10.10.1dns-server 10.10.10.2(Note* I ...

Could you please help me with to configure my ASA 5510 (8.2) and ASDM 6.4 with two outside ISP?Interface Outside 0 -      Public IP     Some services: SMTP, POP, HTTPS and also several VPN (IP sec)Interface Local 1 - LAN 192.168.40.0 / 255.255.255.0I...

Hello guys,Basically I looked in every book from cisco.com about ASR1000 and could not find how to interpret some abbreviated names when viewing the temperatures and sensors info.I am interested in the following:what is "Left"? the location of the se...

    I'm new to cisco 887 routers, I seem to have successfully setup dhcp and can connect to it with a workstation.The 887 can ping internet hosts and telnet to internet hosts but the dhcp workstations cannot.Can some please help me see my mistake.Tha...

Hi everyone,We are having an issue with BGP flapping peer. We have a ASR1002 as Route Reflector and it work fine with all peers except with 2 peers.In logs messages we can see:Oct 19 21:27:49.765 UTC: %BGP-3-BGP_NO_REMOTE_READ: 200.83.0.153 connectio...

I have 2 locations in Nigeria, Lagos and abuja. I wan to share implement 2 internet connections on the 2 cisco routers, one per location.  How do i go about it?Below is the config of the 1st router in location 1:Building configuration...Current confi...

                   I do not see any routed port expansion modules for the 4451-X. Is there a plan for these type NIMs? Or is the four built-in ports the maximum for routed ports on this device?Thanks

I have two ISP connections that I'd like to configure failover and loadbalancing between.  Here is what I'm hoping to accomplish:Example:I have six IP address blocks.1.1.1.1/242.2.2.2/243.3.3.3/244.4.4.4/245.5.5.5/246.6.6.6/24I would like all 6 block...