Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hi all, I have an 1801w connected to ATT/Bellsouth FastAccess via its DSL port. The LAN connection is through FastEthernet1 trunked to an Extreme Networks Summit 450e. My 1801w configuration is attached and everything is working great. My problem: DS...

I was wondering if someone can look at my configuration and tell me what I might be doing wrong in this frame relay configuration? Router 1 is the only one that works. Routers 2&3 line comes up, but the protocol is down. I have been messing with this...

HI , i have a query ,we are planning to upgrade the Sup Engine from WS-SUP720-3B 2 ports Supervisor Engine 720 to RSP720-3CXL-GE=Cisco 7600 Route Switch Processor 720Gbps fabric,PFC3CXL, GECan we use the same old IOS from Sup720 to the New RSP720 wit...

Hello,It appears that the extended ping function in a cisco router or switch has a limit of 9 hops.  Is there any way to increase this?CH-3560-6#pingProtocol [ip]: Target IP address: 10.150.40.60Repeat count [5]: Datagram size [100]: Timeout in secon...

Hi guys,     Just a general question for all of you.  I am running a 1941 isr g2 router, which, according to my specs is equivalent to a cisco 3825 - which i also own.Why would the cpu usage hover around 45% or so with ONE machine running torrents?  ...

HiI'm unable to apply the service-policy to the interface with the config below.majormatic-pta-mount(config-if)#service-policy output CE-OUTPUTInsufficient bandwidth 1024 kbps for the bandwidth guarantee (512)majormatic-pta-mountgrace-mi-ce#sh contro...

wernerleg1 by Level 1
  • 17863 Views
  • 4 replies
  • 0 Helpful votes

            Hello,for a costumer i have replaced there old small home router with this cisco 886.i have configurd the atm interface, and the dialer interface.i get a ip adres in the dialer from the isp , and i have internet connection.everyting works...

Hi,Considering the below network, I am trying to accomplish the communication in green arrows for the request (telnet on port 80) and orange for the reply from the server. Router R1 should NAT communication as indicated by the source (S) and destinat...

Hi all,         Please see the attached file of my network. I have 2 routers with 3 FastEthernet. Both Routers are directly connected through Fastehernet 0/1on both end using EIGRP .Both Routers have 2 ISP links on FastEthernet 0/2 and 0/3. I used EI...

I have a Q in Q tunnel set up on opposite ends of a network. Would I need to disable the snooping for the Q in Q VLAN on the end switches or along the whole path that the Q in Q travels?

sbritz by Level 1
  • 303 Views
  • 0 replies
  • 0 Helpful votes

Lets say we have a routerA that has 2 paths to routerE.  One path goes routerA --> routerB --> routerC --> routerE. The other path goes routerA --> routerD --> routerE.  Assume all metrics are default value.  BGP is configured with an MPLS VRF runnin...

CiscoNutt by Level 1
  • 887 Views
  • 8 replies
  • 0 Helpful votes

                   Noob here. I have done many power calculations for non-Cisco equipment. I found a calculator "cpc" but it did not cover nexus 5k. The data sheet shows specs for the 1100W power supply, but that is just for the power supply. Do I do...

Hi all,This is about a Cisco Asa 5512-X which I configured succesfully for the first subnet to get to internet. Remotevpn to this subnet is working as wel. The Cisco has several ethernet ports and I configured an extra subnet on a new physical port. ...

Hi All,I'm just wondering if there is any documentation that confirms if the 2 built-in Gigabit ports on a Cisco 2851 router support (or otherwise) auto-mdix.I can find information for the modules but not the 2 built-in ports.Many thanks.

Review Cisco Networking for a $25 gift card