Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Hello,Hi would like to set up peer-to-perr VPN connection between 2 VRF (Global and X) with VTI and VRF aware feature.At the momento I'm using 2 IP on public interface (primary and secondary) that are used as VPN peer for VRF global IPsec and X vrf I...

helenio by Level 1
  • 2669 Views
  • 3 replies
  • 0 Helpful votes

Is there a hard and fast rule for the number of eBGP peering sessions you can have per router and once this maximum number of eBGP peers has been reached, you need to start considering more border routers and links? :We have a single Cisco 7606 route...

fsebera by Level 4
  • 624 Views
  • 3 replies
  • 0 Helpful votes

I have two path for one network. I need to use PBR to route to a specific host using path A and other traffic use path B.access-list 101 permit ip any host 10.192.41.35route-map reroute10traffic permit 10match ip address 101set ip next-hop 192.168.10...

jgranda12 by Level 1
  • 1266 Views
  • 7 replies
  • 0 Helpful votes

Hi, I have a bgp peering with my ISP, and it advertise to me just default route, and I see thisB*    0.0.0.0/0 [20/0] via xx.xx.xx.xx, 00:00:23for some reason sometimes I need to remove this route from my routing table, how can I do this?I trying nex...

Hello All,We are moving to Virtual enviornment using Microsoft HyperV, seeking help for best practise configuration for Trunk ports between Blade Switches and Core. Also looking for advice on configuring Backup Network to take backup of Virtual Machi...

Hi Guyz,We plan to terminate Two ISP on the Internet Edge Router and configure site_to_site VPN on ASA connecting to our HeadOffice. ISP One with Static IPISP Two with Dynamic IPAt HQ its a Cisco VPN router terminating VPN connectionInternet_Edge_Rou...

I'd like to enable any firewall features and block any incoming WAN traffic (except for PPPoE negotiaition and return inside traffic) as we use another DSL for incoming to servers.Will just be used for outgoing port 80,443.Could anyone guide as to wh...

M4VM4VM4V by Level 1
  • 944 Views
  • 4 replies
  • 0 Helpful votes

Hi All,I have 2 routers, back-to-back in a lab, connected via serial cable.  Clock rate is 64000.  The link is working fine.  Here is my question.  I configured OSPF on both routers.  Then I type "debug ip ospf events" on both routers.  Both routers ...

Hey Everybody,I'm a little bit confused regarding the current ISR G2 licenses, esp about the temporary activation.Let's say I'm using a 1941 for my own Lab, not for production, and I need to enable the temporary SEC, Data licenses (for 60Days) in ord...

sherif3745 by Level 1
  • 2677 Views
  • 10 replies
  • 0 Helpful votes

Hello,Hello this the night, probably simple but I dont find how to do it... My topology is this like this :      /----- Switch 1 --- R1 --- ISP1      |            |                 |Server       |                 |      |            |                ...

jquintard by Level 1
  • 1087 Views
  • 2 replies
  • 0 Helpful votes

Hi Folks,I have a peculiar problem that I can't seem to get my head around. Hope you can help.Have an ADSL router (887) at a site which has a GRE tunnel to to a 3745.The GRE tunnel is setup with default ip mtu of 1476.If I ping from the 3745 to the A...

pbelletty by Level 1
  • 3275 Views
  • 11 replies
  • 0 Helpful votes

Good Day Guys,I need som assistance with EIGRP that has been kicking my butt for the past few days; Here's the scenario.I have three sites, each site has Internet Connectivity as well as a dedicated local loop in full mesh running EIGRP.All Sites can...

Hi everyoneI hope U are doing wellI have faced configuration of multiple nat/pat  problemPoint is when I paste into router another  nat pool or  nat with route-map or just static  nat  they doesn't work I mean only one of them worksso could someone t...