hi,does anyone have working tcl script for testing isdn line on a router and then sedning alert if line is not ok?br
hi,does anyone have working tcl script for testing isdn line on a router and then sedning alert if line is not ok?br
Hi, my purpose is to have two ISP connections for to have connection failover for my public server.I have a web server and mail server and I would that when primary ISP connection is down automatically my public servers are available with second ISP ...
HiIf configuring WCCP v2 on a router, how many hops away can the Websense servers be? Thanks for your helpKevin
Hi,The router is performing PAT for internet access and I'm trying to enable it as an EZVPN server Using the Cisco VPN client, I'm able to connect it and bring up the tunnel. i can pass traffic by vpn and can ping the local device but cant access it ...
Dear All,We are facing a strange problem in our network regrding IPSec. Below is the config====================================================================crypto isakmp policy 10 encr 3des authentication pre-sharecrypto isakmp key <> address <>cr...
Attached is a rough sketch for my question. Site A is connected to SiteB & C over leased line link.question is pertaining to site B & Site C segments.Site B uses ip segment 192.168.200.0 /24. So in this case assume coreswitch 1 site B to be having 19...
Hi, We are having two 6500 series switches in same floor. In First switch 6748 line cards is installed with DFC-3 card.In our Editing workstations are connected to this line card for higher cache as well performance. In second switch I have installe...
Hi,I would like achieve a load balancing between 2 interfaces (ATM and FastEthernet) for the traffic to route through?How can I achieve it on a Cisco 7206 Router?Thanks,Regards,ken
I am trying to establish a GRE tunnel between 2 routers, within the path another router is performing NAT.From the router at each end I can telnet to the distant end using the my tunnel source as my telnet source interface and the tunnel destination ...
Hi, I need a little help with WAN design. I already have an WAN infrastructure shown at picture (except L2VPN). AS65001 is branch location, and AS65000 is datacenter. Routers R3, R4 and R5 are communicating between themselves using L3VPN. Routers R3...
Hi,For VOIP purposes I need to setup a second PVC (ATM PPPoA) witin my Cisco 867 config. My provider provide me with two ATM connections (using the same line), but the problem is I can't find a good setup guide for this issue. Biggest problem...Iam a...
I'm using 16mbps ADSL2+ line. When I use Zyxel ADSL modem itself connect to internet, I can get actual download speed at 16mbps. However if I connect Cisco 1700 bridge with Zyxel ADSL2+ modem. The internet works but I can get actual speed only at abo...
Hi,Is it possible on a Cisco 867 to configre each port individualy, or only by using Vlan's? Everytime I try to assign a IP to an individual port I get the message: 'IP Address may not be configured on L2 links'. I have tried the following:# Config T...
as you know, the bgp grace-full restart enabled globally on the bgp all-neighbor.but we got the some problem, there is no problem within our network to peer with BGP, but External-BGP with CE has got the problem, the log as"*May 16 04:27:35.549 KST: ...
We are using EIGRP to propagate routes thru VTI with IPSEC from our HQ to our branches, using 3 provider. On one of the link, the EIGRP is often down and comes up right away ( flapping ? ) thus making our link unstable and slow. we are using a same c...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-13-2024 09:04 AM | ||
07-11-2024 01:54 PM | ||
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM | ||
07-02-2024 04:20 AM |
User | Count |
---|---|
14 | |
5 | |
4 | |
3 | |
2 |