Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Routing between L3 core and router

Hi,I have two L3 switches in collapsed core and I need to connect them to one router. I know I should run routing protocol between them, but I do not have support for OSPF/EIGRP.Can somebody give me some advice how to route between L3 switches and ro...

Throttling Bandwidth

Hello,Is there a way to limit the available bandwith on a router to a certain amount of throughput but open it up automatically as needed? Lets say you have a 10Mbps pipe and you want to limit the throughput to 5Mbps on average but if needed it can ...

Automated interface resets

Greetings, i have a 2811ISR with two HWIC-1ADSL Cards installed, each ATM and Dialer interface is in their own respective dialer groups, every day or so one of the WIC cards becomes stale and i have to shut the atm interface then bring it back up and...

Gig E on 7200 without G1 or G2

Hi,Looking at a gigE card(Copper) for a 7204VXR w/npe400, and looking like the C7200-I/O-GE is my only option - Wanted to confirm max mtu on these? (Looks to be only 1524?)...I need at least 1540mtuPA-GE with WS-G5483 doesn't appear to be compatible....

EIGRP stub & multi-access

There is a caveat in the eigrp doc, which says that in a multi-access network, all routers except the hub must be stubs, or else none should be, but it doesn't go into much detail. My questions are: 1.What exactly breaks if there is a mix of stu...

mflanigan by • Level 1
  • 2125 Views
  • 6 replies
  • 0 Helpful votes

OSPF Convergence Problem.

I have two routers, a Cisco 1760 Router with Advanced Security features and 12.4 IOS version, and one Vyatta Router VC.5.0.2. They are ethernet connected and they have full convergence. For IOS version Issues, I had that changes the Cisco Router 1760...

Resolved! OSPF Router-id Change

Hi AllWe are in a process of re-addressing the loopback IPs of routers/core switches.. I have the OSPF router-id associated with each device, which would need to be changed, post loopback re-addressing.. After I re-address the loopback, and enable ro...

sblavanya by • Level 1
  • 45991 Views
  • 10 replies
  • 0 Helpful votes

Resolved! How does ISDN backup work

I am consulting at a company that uses Frame Relay to connect to alot of its WAN sites. They have a backup system that uses ISDN to dial if the Frame ever fails. I was looking at the ISDN router today as well as one of the routers at one of the WAN ...

Questions on policy-maps

I'm looking to configure policy-maps to implement bandwidth levels and I had a question:Using police command, what does the burst subcommand actually affect? Is this the amount of bandwidth that can exceed the average rate?

Resolved! Traffic management on 1760 router

Hi, we have two internet connections at a remote site. The primary connection is a full T1 and DSL as a backup.Is there a way to manage the router traffic to designate the DSL backup to handle all HTTP traffic and designate the T1 for all other traf...

GRE Tunnel recursive routing

Hi Experts, I am simulating a tunnel recursive routing problem using 3 routers. I am using OSPF (area 0)--R0--(area 1)--R1--(area 1)--R2--(area 2) R0 Loopback: 1.1.1.1 /32 (advertised in Area 0)R2 Loopback: 3.3.3.3 /32 (advertised in Area 1) When GR...

Load more