Routing

Hi All, Can someone please help with my IPv6 simple configuration problem?. Two routers on the same ethernet/subnet configured as follows:R1&R2int fa0/0ipv6 add FECO::/64 eui-64My problem is that the "u" between the "eui" was pointed as an erro...

Please explain this statement I got from cisco coc.I."With a 6-slot or a 9-slot chassis, install Supervisor Engine 720 and Supervisor Engine 32 in either slot 5 or 6". Does this mean I am going to instal both 720 and 32 on either slot 5 or 6. Or I wi...

Could any one tell the maximum# of routes in the routing table on 6500 with sup WS-X6K-SUP1A-2GE. DRAM FLASH NVRAMModule Total Used Free Total Used Free Total Used Free------ ------- -------...

Using 1841 with 2x HWIC-1ADSL-M, different ISP on each for resilience. Not attempting outbound load balancing at this point. Default route is out of Dialer0. The problem is that if the Dialer2 drops, the router never tries to bring it back up again [...

Hi, What is the best way to set up a VPN with a 800 Series router and a 2008 server.ThanksSam

Guys we have two routers 2821 which is connected to a layer three switch (which has many routes) now the swicth is nortel one which doesnt support ospf or eigrp......all we can do is static routing....now sattic routes are getting redistributed into ...

Hi, Can we match ACL 101 in L2 Vlan ? How it works with L3 IP mentioned in acl 101 ?vlan access-map Filter-VL7 20 action forward match ip address 101 vlan filter Filter-VL7 vlan-list 7Access-list 101 permit ip 10.0.0.0 0.0.0.25 host 150.1.1.1

Hi, I am really confused with QOS Class-map for http. I am seeing few entry is in inverted comma, few are without, few are coma with asteric like "*root.exe*". Please help if these brackets are required??class-map match-any MIME-URL match protocol ...

Here is my scenario:Location A called CorporateLocation B Called ColoLocation C called MPLS CloudAt Corporate I have one Cisco ASA 5510 running OSPF, one layer 3 switch running OSPF, and a non Cisco router on the MPLS network for the satellite office...

Hi Everybody,I need a clarification on the behaviour of BGP with equal cost path (maximum-paths 2)I have 1841 Router with Dual leased line named my ISP named ISP-1. I was runnning BGP between my router(AS 500) & ISP-1 (AS100). Since the two links are...

Is it possible to configure both trunk and access/voice vlan in a single switch port.i have seen a similar configuration in a live environment.********Int Fa5/12Switchport access vlan 5switchport voice vlan 10switchport trunk native vlan 5switchport ...

I have been playing around with EEM scripts to run this cmd every 120 seconds so I can see how many of my voice Channels are in use on my MGCP Gateway which has 3 PRIs terminating on it.Router# sh mgcp stat | i Inuse Inuse channels: 4This way I can ...

Is it the correct assumption that VRF lite needs to be configured with the same VRFs all through the network for traffic to be routed properly? I'm playing with gns3, and I'm using 3600 series routers. While these support VRFs, I was unable to get tr...

What is the quickest easiest way to achieve some degree of load balancing with BGP?The problem is I have a remote site with 2 T1's from diverse providers. One is ATT MPLS and the other is VB MPLS. It is all eBGP, peering to the interfaces. I have tri...