the version i have on the 6500 is sup-bootflash:s72033-ipservices_wan-mz.122-18.SXF15a.bin. "tracking [tracking number] list" is not available on the ios. can someone recommend the ios that support tracking list for cat 6500Francisco.
the version i have on the 6500 is sup-bootflash:s72033-ipservices_wan-mz.122-18.SXF15a.bin. "tracking [tracking number] list" is not available on the ios. can someone recommend the ios that support tracking list for cat 6500Francisco.
Last time I had a problem with performance on the router 7600 in our external network segment. On the one customer link there were a lot of multicast traffic and my router was broke down. It means that our BGP and OSPF session were destroyed. When I ...
I get this error from a 7201 durring the POST of the router boot. QOS is applied to the WAN interface and I see no other errors in the router.
Hello all!I have a 7513 that has a single FastE circuit and of course a single default route for traffic. I am adding another FastE circuit from another provider and they have provided the /30 WAN and a /24 for LAN.What I am trying to do seems pretty...
%IPCOIR-3-LCCRASH: The card in slot x/y has crashed. Cause Register: 0x0, Signal: 0%IPCOIR-3-CARDCRASH: Card crashed in slot x/yCan someone hwlp me what these messahes are,, and card crashed and came back up by itseld and when i decoded those error...
route-map over route-filteringroute-map over bgproute-map over PBR
Hi all,I am having a strange issue with IPSEC configuration. I have configured 2 cisco routers with IPSEC for the remote sites and the core is having a VPN concentrator.The problem is, both never come online at the same time. If comes online the othe...
I am trying to redistribute a RIP route to an EIGRP process to no avail. Below are the commands:router eigrp 65204 redistribute rip metric 1000000 10 255 1 1500 route-map rip-to-eigrp network 10.33.94.120 0.0.0.3 network 10.33.94.128 0.0.0.3 no auto-...
Hello! The cisco 7201 using for terminate PPP sessions users.Software version: Version 12.4(4)XD10, RELEASE SOFTWARE (fc2)Sometimes cisco crash. The number of users around the peak in 1300. pps around 20-30kAt each of the user interface has a rate-li...
In my organization, we have migrated one of our test networks to 12.4T from 12.3And we had been finding it hard to get all things up and running.Is there any whitepaper on what has CLI have changed that are not backward compatible with 12.4 T ?One of...
I have a Tandberg VTC unit sitting on the inside of my network on a private IP address. I have my router configured to do NAT and have configured a one-to-one NAT for the VTC unit. I am having problems with both inbound and outbound calls. The cal...
Hi,how can i config nat in router..using "Only WAN" ip.ISP has blocked entire /28 lan ip due to some span issue....for time being thought of using wan ip for NATing ... can some one help me in configuring the same ...would be very much appreciated .....
I wolud like to buy a LAN 24port 10/100/1000mbps switch, Fot that I require the model number and its cost
If I have two internet circuits from two different ISP with public IPs, and if I want to implement load-sharing with BGP on these two circuits. Do I have to get AS # from ARIN? or from the ISP?Thanks
HI everybody!Cisco 4500, 6500 switches start powering up the modules from top.If there is sufficient power available then start powering the lower modules. Once all the modules have been powered up and there is still power avaiable, then highest PoE-...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-14-2025 01:24 AM | ||
05-12-2025 03:28 PM | ||
05-09-2025 02:25 PM | ||
05-05-2025 11:47 PM | ||
04-22-2025 12:20 PM |
User | Count |
---|---|
9 | |
7 | |
4 | |
4 | |
3 |