I've experience 99% interrupts on mine 2811 when using nat on 100Mbit link and usually it's not getting more than 45Mbit. Without NAT, cpu load not more than 3%. That's quite surprising me because 1801 at my other site can handle 100Mbit just fine wi...
Dear AllBelow is the script, I am using for internet connectivity on 1841 router.The same scripts works fine at one place but dosent work on clients side.Paragon> Paragon>en Paragon#sh runn Paragon#sh running-config ...
Is the shaper class of service or DSCP aware? In the below example, policy-map 25Mbs-75_24 is applied outbound to a serial interface. It's a parent child policy where it first shapes to 25Mb and then calls the policy map. How does a voice packet g...
Hi Guys,We try to configured a x25 routing from one XOT session to another XOT session.--We do not succeed in making it working.--- The X25 routing from a X25 interface to a XOT session is workign fine- the X25 routing from a XOT session to a X25 int...
Hi Please see the post "Basic Routing Problem" in this forum here is the link http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=WAN%2C%20Routing%20and%20Switching&topicID=.ee71a06&fromOutline=&CommCmd=MB%...
Dear Sir,We have Vsat Connectivity to all the remote locations .we have a hub Spoke Architecture .The users at remot e site are facing problem to access SAp appliations .We have tried with juniper WXc ,Can WAAS help me to acelerate the traffic .Tha...
Hi I've been trying to find the next compatible Network Module to replace the NM-16A/S installed on our 3845 series router. THe above module do data transmition rate of up to 128Kbps on syn/async links according to the Cisco site. What would be the n...
I have a simple applet that I am using to monitor the status of the a serial link...if the link goes down the applet brings up another interface that allows for a vpn connection...I am trying to setup some timer that will only bring up the interface ...
Please advice!!!!!I have two VLAN's in the switch. Vlan 1: 10.10.10.0/24; Vlan 2: 20.20.20.0/24. The proxy server in Vlan1, which is 10.10.10.10I would like to do:1- VLAN2 running DHCP in the switch. VLAN2 should be access to the DHCP server.2- VLAN2...
Hi all. I have a DSL bridge connected to the WAN port of a Cisco 831. For whatever reason, the 831 does not negotiate PPPoE. When I connect a simple Linksys router to the bridge, it works fine.debug pppoe events on the 831 shows the following repea...
Hello,I got an 1841 router and installed a VWIC2-1MFT-T1/E1 card for our incoming PRI. I got the card setup for a T1 but when I try to do the pri-group config I get the following error:%Please configure network-clock-participate wic 0 first%Insuffic...
Hi we have a situation in which we need to be able to terminiate or bundle 8 T1 circuits on a 3845 router. What would be some recommendations? ie what type of cards would be needed, would those cards need to be have built in DSU's?? Any information w...
I have routers that are setup using point to point T1's and static routing. I am coming from a remote location with ip address of 10.101.x.x The DHCP server and other resources are on the 10.150.x.x and the 10.1.x.x networks. The interfaces for the T...
Hi All,I have cisco 2821 connected with an MPLS link which supports two networks (Network A (Data), Network B (Data & Voice))We a new MPLS link willing to terminate on the same router 2821 which will support Network B (Data & Voice)Condition: Network...
