I need to be able to do these commands below. What is the most current IOS that will work for 2811 Routers but supports IPv4 OSPFv3 and where I can locate it. Commands:OSPFv3 123 ipv4 area 0OSPFv3 123 ipv6 area 0
Forum Posts
Does anyone know if the ASR 9XX series routers (902, 903, 920, etc.) support the use of MPLS experimental bits? We have run into issues with load balancing l2vpn over mpls and supposedly using the mpls experimental bits on other platforms works to r...
This is an L2TP VPDN environment running on a CSR1000v in AWS. If I apply a PBR policy via Cisco-AVPair via RADIUS it works every time. However, if I apply a PBR policy via the Virtual-Template then it does not. VHowever, when I first type the com...
Hi all,Its been around a long time but still couldn't find any valid solution for how to calculate interface utilization, let's give you an example -Last 300 sec input rate = 56792 bits/per secLast 300 sec output rate = 146712 bits per sec input band...
Hello and happy new year everyone. I'm working on #CarrierEthernet network with +75 #Cisco ASR/NCS running #EoMPLS #LDP, #OSPF, #L2VPN I wonder if I have to migrate OSPF to #BGP or other IGP as our network is growing fast, currently all Label Switch ...
Dears,Would like your assistance regarding below plzI always read that OSPF virtual-link is not recommeded and should not be used.But Why ? What is the limitation ? Also If I used GRE tunnel instead, will it also be not recommended ? ThanksBR,Sherif ...
Resolved! debug IP NAT iOS-XE
Hello community i´m trying to perform a debug ip nat command on a 4451 router with IOS-XE 16.06.04, however this command appears not to be available anymore. Router#debug ip nat ?<1-99> Access list forcedWORD Access list nameha High Availa...
Hello,I've been getting some alerts from an ASA indicating TCP Reset-I from outside.Example log:Teardown TCP connection ######### for outside: 106.75.227[.]154/42982 to identity:192.168.x.x/443 duration 0:00:01 bytes 4200 TCP Reset-I from outside. I ...
Hello, I'm working with a customer who has a pair of Nexus 9300 for a core switch. They have configured interface mgmt0 as vrf member management, and applied an IPv4 address. They have recently added Meraki MX to the environment to service their ...
Dear All,What is the different if I use etherchannel mode ON in Cisco Switch between two switches, and if I use etherchannel with 2 negotiation protocol (LACP/PagP) between two switches?Thanks,Jerri
Resolved! Natting on ASA for VPN tunnel
Hopefully I can explain this well enough. I have a hub that is an ASA and I want to create a VPN to an asa on Spoke A. The hub inside is 10.19.1.0 and the remote side is 10.1.1.0 On spoke A the true inside is 192.168.1.0 but I am wanting to NAT...
Hi community, I am a little bit confused about configuring HSRP on two sites (two different buildings). We have two core switches placed in two different buildings, which are connected through a layer 2 MPLS connection.We have to realize a scenario,...
Hi all, I have been trying to configure a Cisco 891F router to connect some test vlans using zone based security.I have created 4 zones:out-zone - where my ISP router is locateduser-zone - should have access to the internettest-zone - should only hav...
Hello everyone, I have just been tasked with adding a new subnet to an existing VPN already set up on the ASA. I have no experience of Cisco firewalls and I've exhausted google with my searches so I'm hoping the community can help. BTW we have no acc...
Hello everybody. I would ask you a question regard Tunnel GRE from different VRF.For sure I missing some piece of the jigsaw. I created this simple topology on which I have two ptp connected router and two Tunnel GRE interface in a VRF-Lite: - VRF 2 ...
