Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

Hello All,My company has acquired a smaller company that has a Fios connection and Sonicwall 2040 as their sole connection. They are utilizing an address scheme of 10.0.0.x. My network uses a 192.168.x.x network and BGP/IPFR to network all of the r...

I have some remote offices that are going to have a 2nd T1 line installed which will be used strictly for video conferencing. I know that the 2800 series will support video but will the older 1700 series routers support high speed video conferencing...

Resolved! 2811 specification

Hello All,Does anyone know if I can use the Cisco 2811 router as a layer 2 switch only? I need to replace Alcatel OmniAccess 512's in a network (these are LAN/WAN switches - 12 x 10/100 tx LAN ports and frame-relay over 2 x E1/T1 WAN ports ).I was th...

Dear Sir,I have two IOs images in disk2 of 7206VXR . I want to boot the router with second image which is stored in disk2 . I have already tried boot system flash disk2: IOS.bin command & bootldr but is not working Help on same Aman

amansoi_5 by Level 1
  • 607 Views
  • 8 replies
  • 0 Helpful votes

Hi,As annouce the cisco 1750 router already EOL. Does the new Cisco 4 ports Fast Ethernet Switch WIC and Single Port Ethernet WAN Interface Card compatible with Cisco 1750 router?Can it be integrate into that router?thanks

Good mooring,Please,i need a simple configuration example with vrf between 2 routers acts as PE and P.Regards.

Hi,We have a Site to Site VPN setup that comes into use when the primary links to our London site go down. Yesterday we lost the primary links and along with it alot of connectivity.We use floating static routes to tell our router to pass traffic to...

I am setting up a 2801 with QoS for VoIP. The following QoS config works fine on 1721s, but we are having issues with outbound voice on the 2801s with this policy. The IOS is 12.4(9T)ipbase.policy-map QoS-Policy class VoIP-RTP priority 512 class cla...

bregimand by Level 1
  • 2482 Views
  • 12 replies
  • 0 Helpful votes

Has anyone had to enable OSPF routing on a PIX 525 v6.3? should I expect problems CPU % others issues? the other option is put a 2811 router in front of the FW and in to our core network, so are the ISR routers secured enough to be used instead to b...

bbravo by Level 1
  • 411 Views
  • 2 replies
  • 0 Helpful votes

I have a lab setup for learning BGP. I'm trying to understand why I cannot ping the loopback interface of router c from router b. Three routers.Router A - Lo0:10.252.1.1/32S0:192.168.27.1/30S1:192.168.27.5/30S2:192.168.27.9/30router bgp 65000 no sync...

m.egan by Level 1
  • 908 Views
  • 8 replies
  • 0 Helpful votes

Resolved! 3xT1 and MLPPP

Hello,We are bonding 3 T's with MLPPP on a 2811 router. I am looking for any information on MLPPP configuration. From my understating we aren't doing anything but bonding those 3 T's. Can anyone point me to some documentation or possible provide m...

bfrericks by Level 1
  • 741 Views
  • 2 replies
  • 0 Helpful votes

Hi, I have noticed that it is common for my GRE tunnels to bounce a few times after a power cycle with two log messages that are repeated several times:%DUAL-5-NBRCHANGE: IP-EIGRP(0) 1: Neighbor X.X.X.X (Tunnel1) is down: holding time expired%DUAL-5...

mnewnam06 by Level 1
  • 431 Views
  • 4 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card