Routing

I am attempting to cofigure QOS over a frame relay circuit which also uses GRE tunnels with IPSEC.How can I show that the QOS profile is having the desired affect?

hi,i have a central router (7206) which is connected over ethernet to a central server which does software-distribution.this 7206 is connected to a ip cloud to 200 branchrouter.this softwaredistribution should only get 128kb/s per destinaton - althou...

Hi, can anybody suggest..when i connect consol of cisco 1721 Router. the display is in junk like .. 2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2}2} I could not able to see anything.. setting on hyper terminal...

Hi, I have one doubt. I came to know that some routers with some IOS versions will support software based vpn without vpn modules.is it right?does 1721,1841 and 2821 support vpn without use of vpn modules (i.e, AIM-VPN/EP2-PLUS cards) ?Regardsskrao

Do I need to enter any network-clock-select 0 T1 commands here? I have two data T1s on a single 2MFT-T1. Port 0/2/1 is showing lots of slips/errors (clocking problems), 0/2/0 runs clean. Each T1 may have a seperate clock, I understood the 2MFT-T1 ha...

Do most new T1 installations run over HDSL today and do most T1 lines already installed run over HDSL? I was told by my service provider that my T1 runs over HDSL and that I only use 768 for transmit and 768 for receive which equals a T1 line. They...

I have a 2821 at central site with a channelized T1 on a Network Module NM-2CE1T1-PRI. I've configured a channel group 2 with timeslots 7-8 on this central site router(not a big science). On the remote site I have a 2801 with a service module WIC-1DS...

Hi Netpros,I am trying to establish multiple VPN passthroughs on a CISCO 837. The documentation says to enable this you must do a "ip nat inside source list nn interface BVI xx overload".I looked at the router config and I believe this has been enabl...

I'm having trouble with a multiflex trunk configuration. This is the first multiflex trunk module I've ever tried to configure and my circuit doesn't seem to be working, yet it doesn't seem to be a problem with my carrier. Here is my config:controlle...

Is there a way to block static routes from propagating via BGP?When testing SRST mode; we sent all traffic dest for the Call Managers to null0ip route 0.0.0.0 0.0.0.0 CCM null0Weel this put the phones into SRST mode, but also propagated over the BGP ...

I have a 2811 router with 3 WICs in it, each programmed for a separate HDLC point-to-point T1 circuit. The three remote ends also have 2811s with 1 WIC each. They are programmed identically at both ends, except the "host" end has clock source inter...

Hello,Help is needed on catalyst ios since we are a bit confused.Does catalyst ios support various trains and release types as IOS for routers?Do ALL IOS major releases (mainline train) reach the GD status after a train of mainline's maintenance rele...

I wonder if I can grab some advice..I work on a small network of around 120 users and 30-odd servers spread across 30 switches (made up of a 5-switch 3750 stack, a 3550 acting as a fibre-optic relay and the rest are 2950s and 2970s).Currently the ent...