When i configure one of ethernet interfaces on ASA 5510 as DHCP client it obtaines the lease from DHCP server but it does not release the lease even if i disconnect the interface from the network it stays in "RENEWING" state and show it in ASDM DHCP ...
Forum Posts
I'm looking to setup a full bgp table route lab setup for two dual homed to single ISP to single router.Anyone Where i get lab for it or have lab setup setup?
I'm a bit of a newbie with this Cisco stuff, so bear with me. I have set up port forwarding as follows:ip nat inside source static tcp 10.38.48.21 28919 159.196.177.138 28919 extendableI do know that UDP works since I can connect to all applications ...
Resolved! DNS on a Cisco 2951
Hello,I have a Cisco 2951 and it works as a "DNS forwarder" for my local network. It looks like 'someone' is sending DNS requests from the outside.I see msgs like:2024-03-01T01:13:23.953850-07:00 gateway 516: Mar 1 08:13:22.938: %DNSSERVER-3-TOOSHOR...
Resolved! EIGRP Neighborship Initial Update
Hi, from what I've observed, every time EIGRP establishes a neighborship, the initial update containing the prefixes sent by the router that sent the first INIT isn't acknowledged by the neighbor. Instead, it's always resent using unicast, and only t...
Hello Everyone, I want to create different NAT rules for the same source based on the destination. Assume that I have the private range 10.0.0.0/8 and I want to create two NAT rules as follows:if range 10.0.0.0/8 wants to reach ACL1 then use the publ...
I have a CISCO887VA-SEC-K9 Router and I want to change it, what equipment do you recommend that is similar?
Resolved! Cisco Router
Please suggest a router that has at least four RJ45 ports and four SFP ports, and whose end-of-life has not yet been announced.
Resolved! OSPF LFA on Cisco router
Hi everyone,In Juniper, I can configure LFA for link using: " set protocol ospf area 0.0.0.0 interface ge-0/0/1 link-protection.This allow router to pre-compute and install loop free path in forwarding table.Do we have an equivalent functionality on...
I have an ASR920 that can't load from USB0. The output shows... rommon 6 > boot usb0:asr920-universalk9_npe.16.11.01a.SPA.binLocated asr920-universalk9_npe.16.11.01a.SPA.bin, start cluster is 173301#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#....
I have the following topology in EVE-NG:My goal is to allow Customer 2 clients (VPC4 and VPC5) to connect to Customer 1's FTP server.ISP router has the following configuration:ISP#show runBuilding configuration...Current configuration : 3520 bytes!! ...
I am looking to update multiple Ip routes that we track in HSRP, but the track statement was missing. If I add the track without removing the already configured route, will it update? Or Do we need to remove the route then re-add it with the track st...
I have three WANs; one is the primary and the other two are backups. Primary = dhcp; Secondary = Cellular0/2/0; Tertiary = Dialer1The routes are as follows:ip route 0.0.0.0 0.0.0.0 dhcpip route 0.0.0.0 0.0.0.0 Cellular 0/2/0 251ip route 0.0.0.0 0.0.0...
Hi,I would like to confirm if the boost license upto 1.5 Gbps from the data sheet only supports onboard Gigabit Ethernet Interfaces and not Port channels? We have 400 Mbps bandwidth but ISR 4321 only limits it to 200 Mbps. We isolate the issue and it...
Resolved! HSRP
Hi @All I made a demo HSRP lab with the below setup:R1 connected to Switchport E0R2 connected to Switchport E1VPC connected to Switchport E2R1 connected to a tap interface tap1 (192.176.1.1)R2 connected to a tap interface tap2 (168.172.1.1)Conf of R1...
