Hi, I am still learning all of this stuff but this should be pretty straight forward. I am trying to configure a gateway of last resort for this lab I'm doing for school, I've created a static route every other way and they've all worked. For some re...
Forum Posts
Resolved! Strange Routing Issue to Internet
Above is my network setup, I have a DMZ zone and then the rest of the LAN. The DMZ is directly connected to fortigate and the rest of the LAN is connected with VLAN 1 of the switch to fortigate, the situation is as below: None of the Client PCS can ...
HiI have a TLC device attached to a CE router connected to a MPLS network.From our corporate private LAN I can reach the LAN of the router , 10.201.57.0/24 , my target is to reach the TLC device , that has ip address 192.168.0.251/24 bythe "public" i...
Resolved! OSPF implementation on Core Switch
So let's say I have just 2x Cat4k or 6k that I would like to enable OSPF between (one acts as Core switch where routing for access switches is done and other will be used for access and a bit of a backup, therefor won't be configured for HA) , is it ...
Hi Community, I am tasked with taking our single internet connection (4Gbps) and carve in two lanes. One lane will service normal traffic; internet, vpn, remote access, telephony, etc. The second lane would be dedicated to send backups data to the c...
Resolved! IBGP LOOP
Hi Everyone, May i know how IBGP causing loop? if all the router is at one AS Number. Thanks !
please how can i configure a server to connect with a vlan and a router?
Hello I am trying to configure a Cisco C111-8P and ran into several questions:1. Checking open ports on the router from the Internet using nmap shows that ports 53, 80 and 443 are open.How can you block them for access from the external network, so t...
Resolved! OSPF Cost Calculation
Does anyone know what OSPF uses to calculate cost when the link between it and the next router is a trunk link? I am trying to setup OSPF between 3 different routers, in one connection its a /30 with the ip address configured directly on the interfa...
Hello,I´have a Router CISCO 1841, when it restarts gives the following error:System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)Technical Support: http://www.cisco.com/techsupportCopyright (c) 2006 by cisco Systems, Inc.PLD version 0x10GIO A...
Sometimes, with many Windows updates, the router interrupted the transfer and required a restart. After installing the Bitdefender Cloud Gravity Zone clients, I have to restart the router very often. Interestingly, there is always: WAN (Internet) Inf...
Resolved! Cisco ISR C1111-8 and L2TP Server
Hello On the C111-8P router, I configured L2TP Server with IPSec. When trying to connect, I get the following error: % FMANRP_ESS-4-FULLVAI: Session creation failed due to Full Virtual-Access Interfaces not being supported. Check that all applied...
Resolved! OSFP route filter
Hi all 192.168.1.0/24 is directly connected to gi0/0/2192.168.97.0/24 is directly connected to gi0/0/7 router ospf 1network 192.168.1.0 network 192.168.97.0 How do i prevent 192.168.1x from being advertised out of 192.168.97.x ? Thank you
Hello everybodyI have a question about the OSPF path selection regard Intra External route vs Inter External route.I have this simple topology R2 redistribute the Loopback as E2 in Area 0.In the same way, I have R4 in Area 1 that redistribuite the sa...
My router is Cisco 3640,yesterday I found a new image from web and updated it. Today when I reboot it ,it showsimage unzip failed ,after 4 times reboot ,it change to Rommon 1> model.I want to solve the issue,so view the internet,and a post told me c...
