My question - Would I need to make fa1/1, fa1/2 access ports ?? " switchport mode access " Is it because I already used the no shut command already on the two ports. ??? - The whole point is for desktop 1 and 2 to be able to ping each other, and fo...
Forum Posts
Hello everyone ,I have my infrastructure in my attechement , but what is the ip routing for my server A and D ? Can you check my answer please ? thank youuuServer ADestinationmaskRouterinterface192.168.2.0255.255.255.0192.168.1.1 (R12)eth0192.168.8....
A client bought an ISR 4331 from a RESELLER, then due to characteristics, he bought the IPBASE-k9 license. At this moment, he wants to update the equipment it has a version 3.x.x(classic licensing) to a 16.12.x(so its need smart licensing), then is ...
Resolved! Routing Table
Hey guys, I need some clarification. When it comes to routing for some reason I can't quite grasp it. So here we go. Lets say I have two interfaces point towards each other and I want to route traffic from one to another, what would I have to type? R...
Hi, I am trying to setup our Point-To-Point so that all traffic is going through the VPN and not direct to the internet. Below is the current config (pre existing to me) I have never setup a Point-To-Point to do this. I have used anyconnect and remov...
Hello community.At nowadays by having own AS, and PI /24 networkDoes it possible to devide that network let's say /25 and do advertise each part by peering with two different ISP into global eBGP?I asking cause currious if such networks /25, /26, ......
Resolved! SVI unreachable through vPC Port-Channel
Dear Cisco community Recently I set up a vPC Cluster with two Nexus 5548P both incl. the L3 Daughter Card.I have 3 SVI's (VLAN's 10-13) setup on the Nexus with IP-Addresses configured and on which the Nexus is reachable from my Laptop with both ssh a...
router bgp XXXXXbgp log-neighbor-changesnetwork X.X.X.X mask 255.255.255.0network c.c.c.c mask 255.255.255.0neighbor ab.ab.ab.ab remote-as 7029neighbor ab.ab.ab.ab update-source TenGigabitEthernet0/0/1neighbor ab.ab.ab.ab soft-reconfiguration inbound...
This is not a load-balancing PfR question!!!I can tackle what I need to be done here by moving the nat to the Firewall, but what if we want to do the nat on the router!I have two separate questions..I couldn't find any track operator for the NAT com...
Hi Community, its my first post on the web and i have question on the future network connection.Is its possible implement IPv4+ on the devices (Routers) and what advantages would it have compared to IPv6? Attached Draft: https://tools.ietf.org/html/d...
Hi ForumI am busy investigating this but am currently coming up with no solutions other than additional appliances that need to be installed. What I am trying to achieve is the following:I have a Subscriber based connection (users connect with DSL li...
Hi All, We have BGP peering configured with remote end. Observed strange behaviour. We are learning our routes back to us which we are only advertising to remote end. This is creating a communication issue. Can anyone suggest what happened wrong.
I have a Cisco 3925 router connecint to a Nexus 7K running IBGP. BGP neighborshipis established and I can see a route populated on the 7k via bgp for a loopback networkconfigured on the 3925. Now I try to redistibute the route into OSPF on the 7K but...
Resolved! Restrictions for PBR
Hi everyone,I not sure PBR(Policy base routing) has the restrictions on Cisco 6500 or not . such as IOS Image/IOS Version/SUP . Please advise
Hello, Does anybody have experience with segment routing and ME3400 device? The problem is below: Issues with ME3400 (reload, stuck) devices after clearing OSPF process on ASR920. This issue affected round 30 ME3400 devices in the IP/MPLS network.May...
