Hey everyone, I have a network with inter vlan multilayer switch.I configured dhcp on both M Switches.The problem is that my clients use the MS2 for dhcp and not the MS1, when i shutdown the ports of MS2 , they will use MS1 as redundant Dhcp server, ...
Forum Posts
Hi,I have the following situation described in this article: "https://www.bytesofcloud.net/2018/10/ospf-vpc" show ip ospf neighbors vlan 387OSPF Process ID 1 VRF defaultTotal number of neighbors: 4Neighbor ID Pri State Up Time Address Interface10.25...
Hello, does anybody know if Cisco C1000 Series support the FDPS (Frequency Dependent Pilot Sequence, G993.5 G.vectoring)?
1. Check if Vectoring is enabledIOS router shows the training mode as G993.2 even though the line is trained with full vectoring and this documented with the below cosmetic Bug:Bug Link: https://bst.cloudapps.cisco.com/bugsearch/bug/CSCuw72999Recomme...
Hello everyone, we have an ASR-1002 up and running as pppoe server with radius auth, more than 500 subscriber sessions.We'd like to know if we can see mac address and some info about pppoe clients (brand and model of clients routers and so on)with sh...
Hi, I want configure Dual ISP on ASA 5506-X (based license). I tried this procedure (ASDM mode) http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/118962-configure-asa-00.html But it does not work. When ...
Hi everyone , I would like to talk about qos with vrf-lite and the possibility of interaction between them.I was wondering if it would be possible to classify traffic based on source ip with overlapping subnets each one belonging to a different vrf c...
Resolved! default routes
Hi every one , I had some issues in my lab network, actually all my traffics users go to the internet throught the ISP-01 by defaut route like this : ip route 0.0.0.0 0.0.0.0 a.a.a.a, now i want to make another route to internet by another ISP-02 con...
HI!I want to know about different redundancy how fail over works in Cisco 6509-E with 2 Sup-720-3B supervisors? Do I need to connect those 2 supervisors active and standby via Ethernet cable for fail over or it some kind of internal process?RPR and S...
We have a requirement to handle 15 multicast streams. Currently, we configured PIM configurations on our existing backbone. So, I need to find a suitable router to cater to 15 multicast streams. I selected the Cisco 3925 and Cisco 2951 router. Please...
Hello All, I encounter a problem regarding openvpn connection via ISR router. Simply put, there is one device resided in the LAN side of ISR Router which would be acted as openvpn client. This client is supposed to initiate and actively establish vpn...
Hello, I would like to automate backups of our ASA devices that are installed in remote locations. I want to backup them using Ansible, so the Ansible host will be connecting to the ASA and running backup command to backup config to a FTP server. I'm...
Hello Expert, I tring to convert a Fe lan port to wan port on cisco 892 router. The router that is connect telco provider pppoe device via a switchBoth the switch an pppoe device is supplied by the telco I use the following commad below------------...
Hello guys,I'm Ben, I came to you guys with hope of helping me with a sort of problem that probably no one had. So let's dive in the problem. I have a pppoe connection from my ISP and I set up it on my cisco router with the account password and other...
Hello everyone, i need to configure loopback(hairpin) NAT. If i understand correct i should be able to connect or do ping to my server in my private network from global network(wan). On my screenshot below i configured a simple test network in PT. Th...
| User | Count |
|---|---|
| 13 | |
| 11 | |
| 7 | |
| 6 | |
| 3 |
