Hey everyone, I'm having some troubling figuring out what's wrong with my router configuration.First things first, this is in a lab environment.I have one client(192.168.1.10/24) connected to a switch (default config, no ip routing), which is connect...
Hi,I've got 2 4507er as vss-bundle and two ftd 2120 (running as ha-Pair) should be connectet as Firewall into direction of the internet. The ports on the 4507er should be used as routing ports with one IP-address. Is it possible to run hsrp on them,...
ASR 900 series has label stack depth limitation. Documentation says: "The Cisco ASR 900 router with RSP2 module supports five label stacks."What will happen if ASR 900 series will receive from Croswork optimization engine, SR path including 6 label...
i am trying to add new entry to an existing named extended access-list CORE but when i try to do so, i get this.i cannot get the extended access-list name option 0001(config)#access-list ?<1-99> IP standard access list<100-199> IP extended access li...
Hi Everyone, Need help on how to force the traffic from 10.10.10.1 AWS Server to the Internet over GRE tunnel I have a tunnel established between AWS and Cisco and we have tested to route internet traffic over GRE but it did not go through. I have a...
Noob here, I don't have a CCNA certification, I'm just a home user trying to learn more about networking and make my home network more robust and safer so please bear with me. Here is my configuration: Routerdevice/gateway IP: 10.0.1.1 That connects...
Hi, I am new to packet tracer. I need to ping from PC4 to PC1. Networking is done and its okay when I check via router. But I need to ping from PC command promt but why is it showing my own pc... how can I change that and do the ping in PC4??
Dear Community, Dear Community, I am facing an issue where we are seeing intermittent application connection failures between an internal server and a cloud based DB. When I did a packet capture I found that the failures coincide with the Cloud DB se...
Is there a way to set the session limit for line vty on ios xe v 16.3 ?I do not see a session-limit command under line vty 0 4. I tried ip ssh maxstartups , but this doesn't work. Tested it and saw that the session limit was not set ( show lin vty ...
Hi all! My English is awful, I tried my best, hope you guys could understand what I want to say... 'The decision process entails three phases:Phase 1 calculates the degree of preference for each feasible route in the Adj-RIBs-In. It is invoked whenev...
Hello all.I have an old router. After I accidentally changed a few things in Rom Moniter, I can no longer access Router via console port.There is no error message but as the picture shows, nothing happens. I have tried everything. Can someone help me...
I am trying to solve a routing problem for a customer who have two exits in their network point to the same external network based on N7K core switches. Server1 192.168.80.11/24Server2 192.168.80.12/24Router1 192.168.40.100/24Router2 192.168.40.101/2...
Calling all OTV experts I have configured Multihomed OTV in a virtual lab on EVE-NG using Cisco CSR's. The lab is 2 x CSR at one site both connected to layer2 'customer' switch and a single CSR at a remote site. Everything works good apart from on...
Hi I have a 3750G and would like to know what is the difference between L3 and proper routers as the lines have become somewhat blurredI understand that routers are L3 only and they have the advantage of multiple routing protoclos like rip ospf eigrp...
Hi All, I have attempted to use maximum-paths command under my bgp config I have DNS servers I would like to load balance traffic across however after adding the command, the traffic doe not seem to be load balanced across the intended servers I have...
