I have a test network that I am using for my certifications. I am replacing a Cisco 2811 router and a Cisco 2960 PoE switch with a Cisco 2911 router. I am using SM-ES2-24-P service module in the 2911 for the switch functions. I know the router needs ...
Forum Posts
I've been cleaning and redoing our companies DMVPN setup after we installed new fiber. I broke the work down into chunks so I could test on the weekends so I have a backup of the config before each update was made. Once I got so far into the config...
Hi All, I have a question about EIGRP query propagation within ring topology. For example the following ring topology, here are 5 routers, all the links has the same metric, if the link between A and C down, A will send query to B, B ask E, then will...
Hi Guys,I'm currently reviewing 1 issue and just want to seek your inputs about the current setup and the issue.The setup is there are 2 ISP involve (back-to-back vrf exchange between ISPA and B), Now the issue here's is that when SIP: 192.168.100.1 ...
I have just had a pop-up warning whilst booting up my old but faithful 'Services Ready Platform' router. It basically says that the User Interface will no longer be supported after 31/12/20 because of Flash compatibility issues! This has come as a GR...
Hi allI'm having a bit of a dilemma. I'm running MP-BGP to an eBGP peer and I'm seeing routes received from advertised back to the peer. sh ip bgp vpnv4 vrf Internet_access neighbors 10.91.29.202 advertised-routes*> 0.0.0.0 10.91.29.202 0 100 0 65200...
FTD FP1140 with FDM 6.7. Configured an SLA monitor set to change default route to outside2 interface should outside interface be unavailable. However, I was looking for configuration confirmation for the SLA "failover", and was wondering if NATting...
In light of the recent hacking of SolarWinds Orion we are trying to modify our monitoring system to have the least privileges' to do it's job. I'm trying to create a new SNMP v3 user on our cisco routers that has access to multiple views. However I d...
We have configured and upgrade ASR 9901 device, later we power off the device and after 2 days later powered on the device again. But after poweroed on we saw that, the device configration was full deleted, even the console config. was deleted. And a...
I already tried 2 different ways (2 pictures attached) of configure IP Dynamic NAT and both still doesn't output anything. I saw other posts and I already tried to change the mask to 0.255.255.255 but it still doesn't working. Someone can help?
Resolved! OSPF and BGP
FOr one of our customer , they have two router one in each DCThe router in DC1 is connected to COre Switch in DC1 >> This is a Layer 2 connection Similarly router in DC2 is connected to Core switch in DC 2 ( again L2 connection) The DCs are connected...
I tried to configure my Cisco 1841 routers last night and it was getting stuck at the middle of booting process (pls see copy of the booting message below, also attached). I have configured this routers many times before with no problem but last nigh...
Hi,Problem I am having is I am unable to ssh to a L2 switch from my workstations. I have workstations attached to a L3 switch which is connected to a ASA. This switch hosts the management network(10.20.20.0/24 are servers and 10.20.98.0/24 are works...
So I have this school project that I'm almost done with, but I just noticed a problem, where all the pcs can ping each other just fine, I can also ping all interfaces on my routers without issue. But when I try to ping my DNS server or my Webserver ...
Resolved! mlacp
Hi, I am trying to configure mlacp on 2 routers asr903 but the command port-channel mc-lag on global configuration mode is unrecognized. When I ignore it and apply the mclag configuration the command show redundancy interchassis shows the peer as c...
