Hallo,I would like to understand how to verify the active and standby routers in our network on the core switch. From the snippet below, HSRP is configured on the transfer VLAN 828 to the ISP. The 'sh standby brief' command is not on the NEXUS switch...
Forum Posts
I have Two ASR 1001 but failover for return path doesn't workWorks fine leaving from firewall to ISP Problem when ISP trying to find firewallHSRP active R1 but Internet goes down by BFDtracert says ISP to router 2 10.10.10.2 than die finding to firew...
Hello Everyone. I'm looking to utilize the "show processes cpu monitor" task to view and validate cpu services and usages on a Cisco 4461 Router with IOS version 17.06.05.-I go to use the command and will show the cpu utilization for the first 5 seco...
Resolved! vrf-lite
Hello gentle people,I'm labbing a vrf-lite setup and I feel the config is good. Per the topology, CORP works but PROD does not. The networks behind the core neighbour are pingable for CORP but not PROD. Here's the config for R1 & R2 : -R1#show runBui...
Hello We have ASR 1006X With software image 17.9 How to verify that it will support IPSec configuration? Is it related the rouer image or the license? Please note that, currently we didn't have access to it to verify using command line
hi everyone this topic is been posted few time and there were some solutions but its not working. Below are the logs from a access layer switch(c3650) which blocks the trunk port. this switch is connected to a layer 3 switch(c3850) in that switch its...
i just swapped out a 3850 POE switch to a 3850 non-poe. i upgraded the OS to 16.6.9. then i copied the config back to the new non-poe switch. now i cant ping or access the switch via the network. constantly getting %SPANTREE-2-UNBLOCK_CONSIST_POR...
Bonjour,J'ai un VLAN bureautique en 192.168.1.0. Mon CBS350-8T-E-2G a l'adresse 192.168.1.240.La passerelle par défaut est le 192.168.1.1.J'ai un VLAN formation en 192.168.80.0. Mon CBS350-8T-E-2G a l'adresse 192.168.80.1, le dhcp fonctionne parfaite...
The document Cisco Nexus 9000 Series NX-OS VXLAN Configuration Guide, Release 10.2(x) - Configuring Layer 4 - Layer 7 Network Services Integration [Cisco Nexus 9000 Series Switches] - Cisco describes a scenario with a firewall connected to a VxLAN fa...
Hello i have cisco 1921/k9 when i first do a factory reset and configure the router the internet works until the next day then i have no internet connection. I am using cable modem connection with spectrum which is my isp. i am using the following c...
Dear Expert,Hope all is well.One of cisco route 2921 reboot it unexpectedly and upon checking, we find out below result:cisco router reload reason bus error at PC 0xB0D0B0D, address 0x0.the firmware version: c2900-universalk9-mz.SPA.157-3.M8.binthank...
Hi ,how to configure snmp ver 1 or 2c in cisco n540 router.Please provide me command please.Thanks,Prashanth
Hello,I wanted to know if: Can you designate an IP address from a BVI interface as a Default Gateway to all kinds of end point devices connected to any of the interfaces belonging to the bridge group?Should it be possible to ping that interface from...
Hello everyone,Currently seeking assistance in identifying the issue.We have two ASR 9006 routers located at two different sites. Both routers are running OSPF between them, utilizing multiple sub-interfaces, with each sub-interface assigned to a dif...
Hi ,I want apply default route in Cisco N540x router.But i am not able to find ip route command in router.Can someone help me which the comand for that.Thanks,Prashanth
