Forum Posts
I've purchased the license and save it on flash:I understand I will need to do the following.license install flash:/<>.lic but do I need to do after this? it's not clear on the website current license levelLicense Level: adventerpriseLicense Type: Pe...
Hi,We have a pair of ASAs, and we use the prompt hostname state command to display the active or standby status in the hostname.Now, we have a pair of FTDs managed via FMC. We sometime need to SSH into the FTDs to check the configuration, we are look...
Resolved! Extended ping vs regular ping
Im trying to understand the difference between these two pings below on my cisco 8200. xxxxxxxxxx#ping ipTarget IP address: x.x.x.41Repeat count [5]: 2500Datagram size [100]: 1500Timeout in seconds [2]: Extended commands [n]: yIngress ping [n]: Sour...
on configuring NCS 540 model router.Getting message as "Invalid number(-96) sent as ASCII value to command-line process from VTY/TTY, refreshing prompt."
So, I have configured OpenVPN on a number of systems with Yealink Phones.I just have to map port 1194 UDP through the Firewall. I works with every kind of router I have found. But on the ASA it will work for a few hours then just quit. Wait a few mor...
Resolved! QFP Load on C1111
I often get the following error when I load a router with traffic. %IOSXE_QFP-2-LOAD_EXCEED: Slot: 0, QFP:0, Load 85% exceeds the setting threshold 80%.5 secs traffic rate on QFP: Total Input: 31561 pps (31.6 kpps), 274136312 bps (274.1 mbps), Total ...
Hello everybody, I want to gather OSPF Opaque-lsa information (used for segment-routing) through YANG SUITE/ NETCONF but the c8000v device doesn't show me any information. Particularly, I need gather Adj-SID and Prf-SID information. I've tried sever...
In the release notes for IOS-XE 17.5.x it states that minimum ROMMON versions are: IOS-XE Minimum ROMMON17.2.x 16.9(1r)17.3.x 16.12(2r)17.4.x 16.12(2r)17.5.x 17.5(1r) However the latest ROMMON available on CCO is 16.12(1r). W...
Resolved! Can't ping
Hi I'm new and unexperienced in packet tracer .
Hello guys,We search an alternative for CISCO886-VA-J-K9 it support Annex J for Germany implementation.The router needs to perform 250mbit vectoring. We are looking for alternatives. Cisco writes C1117-4P while I think it is wrong, or can we use th...
Resolved! bgp bfd and timers
Hello what's the purpose when we using bfd and at the same time using timers and does has any pros and cons.for-ex i config bgp timer 5 10 and also in some of neighbors configure bfd what the purpose like this configuration or when we setting bfd we ...
Hi Everyone,A weird routing behavior happened between 2 routers and I'm looking now at some explanation to understand. We configured OSPF (broadcast) between 2 routers (R1 and R2) with a redistribution of a default route from BGP to OSPF on R1. R2 wa...
Hello,This is a question on ip assignment between our APs on our 9800-40 WLC. I work in a school district. We allow or deny student access to YouTube by leveraging unique policy profiles that have different assigned vlans based upon which AP needs to...
Resolved! BGP Peering with Loopback Interfaces
Hello,I been using BGP peerings with loopbacks for a while, but I am trying to understand the reason for it. I've searched in other Community Discussions but I could not find any answers:A lot of answers use the following scenario, where is clear tha...
