Hi, I hope you can help me, I need the CAD drawing 2D & 3D (DWG, DXF, or STEP) for the following component. - CISCO Router ISR 4431 (or similar) Many thanks in advance.
Hi, I hope you can help me, I need the CAD drawing 2D & 3D (DWG, DXF, or STEP) for the following component. - CISCO Router ISR 4431 (or similar) Many thanks in advance.
what does this term mean? can you give me an example?sorry for the noobish question
what wrong ?Cisco 891f speed internet too slowBuilding configuration... Current configuration : 2531 bytes ! ! Last configuration change at 08:38:27 UTC Wed Dec 25 2019 version 15.3 service timestamps debug datetime msec service timestamps log datet...
Hi all, So just a quick one, I have acls configured on a router but not applied to any interface (LAN or WAN), but they seem to work.I also have nat configured, static and PAT, could it be that the NAT "inside" or "outside" automatically does the job...
I'm confused for the answers on Figure 3. I understand the bottom 3 answers but the first 2 make no sense. There are other IP addresses that are higher than their own networks yet they were chosen for the DR (priorities aren't in this activity). Also...
We're running SDA. Our External Border Nodes are iBGP neighbors and each have an uplink to the two Fusion Routers (eBGP). I logged into each of the EBNs, turned on term mon, and then typed debug bgp ipv4 uni <neighbor IP>. Instantly the screen was fi...
Hi,Can someone explain me which is the difference in configure the conf-reg value in 0x102 or 0x2102?Thanks a LotEmiliano
I am trying to block 192.168.0.0 to 192.168.3.255 network by standard ACL but permit the 192.168.4.0 and 10.10.10.0 network. My ACL access-list 15 deny 192.168.0.0 0.0.3.255 , but unfortunaitly i unable to ping from my 192.168.4.0 network also when ...
Hi, I have install the license in ASR9001. I have install the MPLS package as well but whenever I get the output os "Show License" it shows license is inactive as under. RP/0/RSP0/CPU0:ios#sh licenseWed Jan 8 00:47:59.925 UTCFeatureID: A9K-9001-AIP-...
Hi, I had created a unique subnet @ 192.168.44.1 instead of 192.168.1.1 but every time there is a power failure the RV260W router resets back to 192.168.1.1. Kind of annoying.. Firmware bug?? Thanks
Hi, Have an RV260W and need one more open port for networking connections as all 8 ports on the back are all occupied. Anyhow I notice there is a console port that looks like an ethernet port and was wondering if the firmware allows that port be assi...
Is there a command to check if the DRAM and the compact flash are working? I have an 1841 on my test network. I need to use the K9 IOS for SSH login configurations. It's in flash but the K9 IOS can't load into NVRAM startup. I think the DRAM is bad. ...
I have a question regarding Static PAT I have a topology with HTTP server , router and PC.I tried to pat on a router with the following command :# ip nat inside source static tcp 192.168.1.10 80 1.1.1.1 8080all ports configured correctly g0/0 as in ...
Hello,we have a 2901 Cisco router with 2Mb bandwidth with access to a remote site (data center) so we have 2 servers A and B we want to limit the bandwidth for accessing the server A to a 512Kb Max for all users (Not per IP) how can i do that and ...
Hi, We have Express Routes from our datacenters to Azure connected with BGP.In between is our provider.We peer with BGP with our provider which in turns connects to an Express Route provider which peers using BGP with Azure. Now we want to use BFD t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-06-2025 04:13 AM | ||
02-06-2025 12:47 AM | ||
02-06-2025 12:03 AM | ||
02-03-2025 09:24 PM | ||
02-03-2025 07:43 PM |
User | Count |
---|---|
17 | |
9 | |
8 | |
8 | |
5 |