Hi everybody! For the past weeks, I´ve been trying to figure out what´s happening at one customer´s network. It has 2 fiber connection with the same ISP, one connection with pseudo-fix IP and the other with dynamic IP. The Cisco3945E is behing both I...
Hi community,Green hand, first question here, probably a naive one, but I searched and couldn't find the answer. I'm not sure if this is the right board to ask. If not, please kindly let me know which one I should post to. I'll try to provide as muc...
INE foundation lab 1 - DMVPN eigrp keeps flappingHello, i am working through foundation lab 1 and I got to the DMVPN phase 3 portion and I got stuck. R1 is the hub, R5, R9 and R10 are the spokes. When I enter the solution on the routers, the link fr...
Hello Experts,I need a helpful advice regarding VWAAS-RTU-1300 and ISRWAAS-RTU-750 license. Recently I've purchased a Cisco ISR 4331 router, with which I have got these two licenses. Now I've done google several times about these license, but couldn'...
Hi, woundering if someone have comeacross this issue and can explain why it's working on some platforms as I have not been able to find a document on CCO that explains this behaviour.The issue is that the configuration fails when putting a simple egr...
Hello, recently I deployed Cisco 2811 router as CME, I have several phones and computers operating on different vlans (VLAN 10 VOICE 10.111.10.0/24, VLAN 20 DATA 10.111.20.0/24). I created two subinterfaces on the router with dot1q encapsulation and ...
i I have requriment to advertise default route to BGP peer only if DEF route is present in routing table. R1-ISP (1.1.1.1)..............(1.1.1.2) CE1 (2.2.2.1)----------(2.2.2.2)CE2 - Default route is configured on CE - #ip route 0.0.0.0 0.0.0....
Our current CPE router of choice is the C1111-8P & C1111-4P (and variants depending on the requirements). These are supplied with a rack-mount kit which is relatively easy to assemble although you do end up with lots of spare screws.The guide on CCO...
Hi All, Could you please share the licence difference between lanbase and IPbase. Regards,K
Cisco Novice here and could use some help... I just purchased 2 RV340W for each office to replace 2 GB-800e routers at our 2 offices. We currently have Telepacific 1 NET MPLS which connects the 2 offices. Currently both GB-800e's have static routes...
Dears ,I have 3 routers ( A, B , C ) .. The peering between ( A and B ) (iBGP) , Router B is ASR9K , and the peering between ( B and C ) (iBGP) too . I need which prefix receiving by the peering ( A to B ) , Router B immediately advertise this pr...
So, this is just a quick call for help. I am trying to understand how to implement network to network tunnel between a new ISR1117 and ASA 5505. We have previously been using 800 series ISRs and the ipsec vpn config is very straight forward. I assume...
I HAVE TWO LINES WITH FIBER OPTICAL IN THE ROUTER BUT INSTEAD OF BALANCING IT GIVE ME VERY LOW BANDWIDTH.IS THIS ROUTER ABLE TO MANAGE FIBER OPTICAL?
I have a client who has a Cisco ASA 5512 device with, among other things, an inside interface dubbed "InternetOnly" on an internal 172.28.0.0/24 network. They also have a single outbound interface with a small IP block in use coming in for varied usa...
Hi everyone, I can't seem to send packets across my network. I have WAN set up and traffic within each LAN works but can't seem to send anything across the routers. I have configured static routing and have sub interfaces set up to handle the vlans.....
