Hello I have a working system coming from another Thread which was solved but now I am curious if how I got it all to work was correct or a forceful band-aid. https://community.cisco.com/t5/routing/can-not-get-internet-access-or-nat-translations-on-...
Forum Posts
Hi everyone, We’re running a dual-hub DMVPN (Phase 3) environment on Cisco ISR 4400 routers (IOS-XE 17.9.x).All spoke routers are dual-homed — each forms tunnels to both DC-A and DC-B hubs. Recently, several spokes lost their BGP peering with DC-A, w...
I setup a site to site VPN with a pair of FTDs using the FMC VPN wizard and static VTI interfaces. Each FTD has two ISPs so I configured a backup tunnel using the 2nd set of ISPs and VTIs. I also setup BGP using the primary set of ISPs and VTIs. All...
Hi team, I have a device: C8200L-1N-4T and NIM-2FXSP. I want to "show voice port" on CLI but it's doesn't work. I haved show the commands "show inventory" and confirmed that the NIM-2FXS module is detected, so why am I unable to run the show voice po...
Hello Support,I have a LAN with a Distribution switch 9300 and Access switch 9200. 9200 series support L3 routing, my question is about implementing L2 network with Trunk or implementing routed access Network with OSPF. which is the best architecture...
Hello Cisco Community,The router Cisco 4321 gets stuck when trying to load IOS : isr4300-universalk9.17.06.05.SPA.bin and get the following error:%IOSXEBOOT-1-INVALID_IMAGE: (RP/0): Incompatible hardware and software image version; newer software ver...
dualstatic Hello, We have a dual ISP setup on a Cisco 927 using FTTP (primary) and SoGEA (secondary), both via PPPoE and controlled by IP SLA/Route Map.When FTTP is active, the SoGEA connection becomes unreachable, preventing proactive monitoring of ...
Dear community, In a VXLAN topology with VRFS, where routes from VRF2 or VRF3 are imported from VRF1, these routes are not being advertised to a firewall located in VRF1. I've attached the configuration of one device. It's as if the route isn't bei...
Hei all, I was trying to find any information about this upgrade path through release notes, but it is lacking any information about steps in the upgrade. I was also getting through some forum topics already posted and went through few. It would be g...
I don't know how to solve task 6 and 7 simultaneously when we have to use two distribute list on a same interface. One for the access list on R2 and second for the prefix list on R2 towards R1. I need a solution ASAPRouting, EIGRRouting, EIGRPP
Resolved! Cisco 3825 Last IOS version
I have old router series 3825 and running using version 12.4(13r), and want to know which latest version for this router? I try to lookup 3800 or 3825 in the software download but not found.
hi team,I have c9300 connected to SRX 340 via static route. I have also VRF on this switch with vrf default route through global. the VRF has source multicast and needs to get out through global routing table. VRF config po11no switchportip vrf for...
Resolved! ACL doesn't work
I am doing a lab on Cisco Packet Tracer and have reached the ACL stage.The course begins by giving small examples so that we can learn and understand the concept. But these examples do not work. I have been working on this for two hours, searching th...
Hi Community Members.,I set up a Failover /Load Balancing on a Cisco Router using Dual ISP and DUAL LAN segmentAs shown below:From the Edge Router: Config.track 1 ip sla 1 reachability!track 2 ip sla 2 reachability!interface FastEthernet0/0ip addres...
Hello, I am trying to setup an IPSec VPN to a set of firewalls and I don't appear to have the isakmp commands under crypto. I read another post that I may need a separate license, is that still the case? Thanks for your help! (config)#crypto ?...
