Server Networking

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco UCS X-Series Energy Efficiency Offer

 

Forum Posts

I would like to verify the dhcp lease time.  The time is calculated from the moment a client receives a lease, not from when the dhcp server has set a release time.  Example.  A client requests a dhcp lease at 8:03am.  DHCP lease time is set for 24 h...

pokadave123 by Community Member
  • 1025 Views
  • 2 replies
  • 0 Helpful votes

Hi all,I have two 5K's in a VPC configuration.  I'm trying to figure out how to connect the 1000v using CNA's, especially pertaining to FCOE.Currently we have servers with a 10 gig connection to each 5K using VPC-HM.  In addition to the regular traff...

NguyenT11 by Frequent Visitor
  • 4461 Views
  • 9 replies
  • 0 Helpful votes

Hi everybodyI would like to know how to configure all nic interfaces of all ESX server that contain the VEM ou VSM module on vSphere client ?* For ESX that contains the VSM module, I added another nic* For ESX that contains the VEM module this is the...

boub91 by Level 2
  • 3171 Views
  • 6 replies
  • 0 Helpful votes

I am trying to install teh demo license for the 100v and I get a message that"A licenese with a later/different expiry date already exists for feature" message. When I do a show license brief, nothing shows up.  Any thoughts?

david.chinea by Community Member
  • 1552 Views
  • 1 replies
  • 0 Helpful votes

Why doesn't cdp neigh show both ports like 1/1 and 1/2 of the port-channel other than mgmt0? I have the same cdp output on the other N5kN5K-EDGE2-DC(SSI13500AD5)mgmt0         145    S I s     N5K-C5010P-BF mgmt0N5K-EDGE2-DC(SSI13500AD5)Eth1/2        ...

aamercado by Level 7
  • 769 Views
  • 1 replies
  • 0 Helpful votes

On the N5k-B set at priority 105, I cannot see interface 101 of the fex, but can see inter 101 on "priority 110, n5k-A" why is that? when I do a sh vpc brief, adj is up alive. I went ahead and powerdown the N5k-A and now N5k-B has inter 101....so can...

aamercado by Level 7
  • 1315 Views
  • 1 replies
  • 0 Helpful votes

I am getting this error on E1/7 and E1/8..what am I doing wrong?. Thxinterface Ethernet1/7  switchport mode fex-fabric  untagged cos 0  fex associate 101interface Ethernet1/8  switchport mode fex-fabric  untagged cos 0  fex associate 101N5k-Edge1-DC(...

aamercado by Level 7
  • 3786 Views
  • 1 replies
  • 0 Helpful votes

Hi,Please consider this scenario, where L2 VLANS are spanning 2 data centers and where R1-R4 are L2/L3 N7K routers (replacing existing 6K).(I wish VSS would be available also in N7K to make life 10x easier!!).                      R1                 ...

Not sure if you take other vendors and then “ciscolize” it (ie HP or IBM to MCS Callmanager) but do anyone know if Cisco also ciscolize the SFP cables?I see 7meter cables available below via other vendors. All the vendors (including Cisco) uses the s...

aamercado by Level 7
  • 1104 Views
  • 1 replies
  • 0 Helpful votes