hello everybody.
according to the doc
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus1000/sw/5_x/security_config/b_Cisco_N1KV_VMware_Security_Config_5x/b_Cisco_N1KV_VMware_Security_Config_5x_chapter_011.html
there should be a VSD ...
I've run across an issue with a new 5672UP switch and GLC-T modules that I was hoping someone had an answer for. When I insert the GLC-T modules into the 5672UP and plug in another device (via CAT 6 Ethernet), the other device (an ASA in this example...
Hi all,
I need to upgrade a pair of NX5K due the bug CSCuq16049.
To prepare the the upgrade I want to run the following commands but I want to be sure that they don´t have impact on the service (high cpu or disrupt the services on FEX or the NX5K)
Th...
I trying to usse VLAN SVI as peer keepalive interfaceSo i assign IP for the SVI, as Nexus-A is 1.1.1.1, Nexus-B is 1.1.1.22 interface assign as vpc peer-link, and confogure as port-channel. 1 interface assign as peer keepalive purpose. question01. wh...
Nexus 2348TQ Fex with 40 Gig uplinks ports does not come online with parent switch Nexus5672UP
Without doing interface breakout the ports will not even show as connected on the Nexus5672UP ports towards FEX. Now after we configured the interface brea...
I'll start by saying my collaboration/datacenter knowledge is not a strong point. I'm trying to assist a customer and am having a hard time finding the right documentation.
The customer has existing BE7Ks for their collaboration suite. They are purch...
Hi,
I need to capture traffic from 10 ports on N5020 fex N2K-C2248TP-1GE. One of my concerns is:
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/configuration/guide/cli/CLIConfigurationGuide/Span.html:
"The switch supports a m...
Hi, All
We have 2 93180YC-EX with FEX 2348TQ, NXOS: 7.0(3)I4(2).
And we have problem: fex ports don't communicate properly with connected devices.
Neither like L3 ports, nor like L2.
We have simplify our test configuration to troubleshoot this issue ...
Hello, I know this thread is quite old.
But I need your help, I´ve configured two N5K and they're sharing the same vPC domain... and the peering Keep-alive is attached into mgmt0 in case of failure of one Keep-alive link all vPC(Port-channel) become...
We are planning to deploy ucs infra using Python scripts. Is there any example scripts like create service profile using Python. How to connect ucsm 3.1 using Python..
I read still Python SDK is not available. If this is the case then which tools are...
Hi everyone,
We have an UCS system with B200-M4 blades.
There is a faulty blade that totally failed (except HDD pair) and need to be replace. We try to keep the OS and application on old blade as they are, by:
1) Disassociating service profile from f...
Hello Foloks,
Greetings !!
When I am preparing Cable Matrix to configure a new UCS POD we are using IPMI and KVM IPs. what is the difference of KVM and IPMI IP ? Can anyone help me out to understand about the IPMI IP ? Why do we use IPMI IP? How I ca...
Hi
Im trying to install Cisco APIC-EM ver. 1.4 on a Cisco UCS C200 M2 with bios build 1.4.1.0 (7/13/2011). When i plug in ethernet cables the mgt int. and eth0 int. there comes link on both. Now i insert the APIC-EM DVD and start installing the appl...
Good evening,
in our lab I set up a normal Nexus 5672 pair with two FEX.
VPC-Peerlink between the 5672 and VPCs to the FEX - eVPC so that they're connect redundantly.
Also a fresh DCNM installation is connected to this equipment but there seems some...
