Hi , Thank you so much . Does anyone have any idea how to onboard the stackwise virtual into fabric , as of today LAN automation is not supported.Im thinking of below approach , really appreciate your valuable suggestions. 1> Manually configure the...
-
-
-
-
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community
-
Forum Posts
Hi All,I operate a small number of SDA fabrics that all use the Deny-List (default Allow) Group-Based Access Control/TrustSec Model. I am not considering changing these to use the Allow-List (default Deny) model, however I'm aware that if the Default...
Hey all, I'm trying to provision a fabric device as a border node, and I get the following error: Failed to add device SW400-1.adamlab.local to the Fabric Site/Zone since 'ip routing' is not configured on the device. Please configure ip routing on th...
Hi All,I'm currently deploying a multi-site SDA fabric and I wanted to find out how others are managing the VLAN IDs that are assigned to IP address pools.When testing, DNA Center auto allocates VLAN IDs to IP Pools starting from VLAN 1021, however t...
Hi!We have built a SDA network but discovered that the access switches no longer send switch/port to the DHCP-servers.In our old network we used "ip dhcp snooping information option format remote-id hostname" on the access switches to be able to inse...
Resolved! DNAC Question
HII see in our DNAc that in Inventory we can add FMC devices now, Can anyone tell me if I can still add them when the FMC is not part of the SD Access, and if so when added what am I able to do to the FMC once added , also is it no disruptive adding...
HiIs it possible to hand off the same L2 VN on multiple borders ? I know it's not recommended to use the Border/CP for this function but I'm just exploring possibilities here. So, for example, I have 2 Borders (either L2 only or Border/CP nodes). ...
Hi,What is the point of redistributing BGP routes into LISP in SD Access?
HiAre there any special considerations needed for SD Access multicast when you’ve deployed an extranet policy. I’m doing some testing and previously got intra-VN multicast routing working fine. Now I have deployed an extranet policy to use the Infr...
Resolved! SD-Access Transit Multicast support
Hello, I'm currently assessing the SD-Access Transit for a multi-site SDA deployment.At CLEUR2020, I've noted that multicast was not supported between sites when using such type of transit. I'm unable to find a documentation stating whether or not mu...
Resolved! SD-ACCESS DESIGN
In the figure below, the control plane nodes are interconnected with the borders nodes.In the SD-Access Fabric Design document, it is mentioned that intermediate nodes interconnect and provide IP connectivity between the devices that play a role in t...
Hi guys, today I have a little problem with SDA-transit and I am not sure, if I am doing it wrong or DNAC (or CC). I have a customer and we want to migrate to a SDA fabric solution. The customer has different remote locations where we can use higher ...
Hello, I have a 9800-40 WLC running 17.9.4a code if I use the Service Port IP as the discovery IP in DNAC it is not properly used as the source tacacs and radius interface, the issue is I have a different IP configured for the WMI, DNAC configures th...
Dear friends,We are planning to deploy new SD-Access and SD-WAN infrastructure, but I had a few questions:Is it possible to connect remote branch SD-access equipment (DNA access switches) behind SD-WAN router? I mean to see it in Fabric, configure vi...
Resolved! LAN Automation fails
HiI'm trying a very simple LAN Automation test where I have one Border manually configured and discovered which I am then going to use as a seed device for my second Border. When I start the LAN automation process the second Border upgraded to my Go...
