Software-Defined Access (SD-Access)

Resolved! Can a FIB node have a downstream Edge node uplinked to it

Hello Cisco Community, I understand that for SD-A supported topologies, a FIB node has historically been deployed for very small sites consisting of a single network closet. Though multiple switches can be deployed in such a site, in such cases they...

Resolved! Fabric VNS Scale

If I have a fabric and I add 9200 series switches that support only 4 virtual networks.. does that mean the entire fabric is limited to 4 virtual networks even if I have 9300/9500 deployed in the fabric..... I would not think so but looking for data...

Resolved! INFRA_VN DHCP for the APs on the border

Hey all,I'm wondering if there is any technical reason to why we couldn't put the DHCP server/pool for the INFRA_VN on the border nodes.As long as we put a pool on both borders for resilience that is the only thought I have. Currently, we don't have ...

Border GW interface address configuration

Hi,why border GW needs to have a loopback interface configured with the same IP address as anycast gateway?As far as I understand, this is because the border GW needs to advertise this network to the external L3 network and by configuring loopback wi...

Borders upgrade problem with EWLC

Hello We recently encountered a problem with upgrading Border devices which are running EWLC with HA. We are not able to start software distribution because devices did not pass prechecks (N+1 check failed, please see attachment). Wireless configurat...

DNAC ISE integration without pxGrid

Our organization is not allowed to use pxGrid... so in this cse how do you integrate DNAC with ISE? How would the policies created in DNAC be pushed to ISE with pxGrid integrating them together? Thanks!

Cisco DNA Center Smart Account Specific Level Access Required

Dear Everyone, I have tried to integrate DNAC to Smart Account but i notice that It got error with level of access. Is there anyone know the specific level of access for integrate Smart Account to DNAC. Note : My level is Smart Account User Thank...

Resolved! Lan automation - one link blinks orange

Hi Guys, When im deploying a new switch via lan automation my new switch gets an orange light indicator on the primary seed but the secondary link gets a green light. After the deployment the primary link goes green. I can see the devcies in cdp neig...

Does 9300X platforms support SDA border function?

Does the new 9300X platforms support co-located border/control plane function in SDA? This doc mentions it supports in control plane node scale table, but no mention in the table below it for border scale. https://www.cisco.com/c/en/us/products/colla...

Catalyst 9300 DNA Expiration

I'm going to renew my DNA for C9300 switches, but I see that I can only renew DNA through March 2025. I have read that after expiration the switch will continue to function, but I would lose Network Advantage rights. My license shows as perpetual t...

Resolved! DNA-C Question

HiIn DNAC we have an image marked as golden for all our 9300's is it ok to mark another image as golden so I can do a test software upgrade on one edge node ?, marking the other image as golden wont trigger an udate of all devices will it.?? Thanks

FTD as fusion device

Hi, I have some questions related to FTD as fusion device. (1) Ciscolive 2022 Las Vagas BRKSEC-2845 (see attached) shows two possible topology.- Direct FTD attachementDNAC can only provision L3 handoff using /30, not /29 or /28. Hence, if i do this, ...

Resolved! cisco catalyst 3560cx SDA extended node PnP fail

I tried to add catalyst 3560cx as an extended node to SDA fabric but I have this error message: Device tried to contact the server and failed during certificate_install how can I resolve this problem? is it possible to add extended node without using...

Visio Stencils for SDA

Hi,where can i find Visio Stencils, Shapes or Templates like the Graphics in the typical Cisco Live Presentations for the SDA-Family.it would be very practical to have the graphics from the presentations for DNAC, ISE, Border/Controlplane Node, Edge ...

Resolved! How to troubleshoot BUM multicasting?

HelloWe have an SD-Access infrastructure and L2-only vlan with PXE hosts. The FW is a DG for that VLAN and it connected thru L2 handoff.The problem is that PXE hosts can't boot for dozens of minutes after reloading the edge switch they are connected ...

Software-Defined Access (SD-Access)

Forum Posts

Resolved! Can a FIB node have a downstream Edge node uplinked to it

Resolved! Fabric VNS Scale

Resolved! INFRA_VN DHCP for the APs on the border

Border GW interface address configuration

Borders upgrade problem with EWLC

DNAC ISE integration without pxGrid

Cisco DNA Center Smart Account Specific Level Access Required

Resolved! Lan automation - one link blinks orange

Does 9300X platforms support SDA border function?

Catalyst 9300 DNA Expiration

Resolved! DNA-C Question

FTD as fusion device

Resolved! cisco catalyst 3560cx SDA extended node PnP fail

Visio Stencils for SDA

Resolved! How to troubleshoot BUM multicasting?

One-way Audio & Intermittent Unregistration Post-Phone Replacement

Use ISE pxGrid to locate jabber clients using CER

SD-Access FIB loopback0 change IP

Cisco DNA Center - unable to remove edge node from fabric site

Network Templates filtering by Site shows irrelevant templates

BGP routes filters in Catalyst Center automation

Trustsec Enforcement

PXE boot on SDA not working

In SD-Access, one VN can carry how many subnets?

Bitlocker Network Unlock in SDA Environment