Switches - Small Business - Page 310

Looking for support docs and videos? Check here

We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...

Helpful support links - Updated September 2023 w/ Catalyst 1200 - 1300

(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...

SGE2000 slow forwarding as accessswitch with LACP to SG500X stack

Hello everyone,Question: Does any body know why ports on my SGE2000 take so long (>60s) before forwarding packets to the end user systems (desktop computers).I got two SG500X switches stacked in 10G mode and got two SGE2000 switches connected in LA...

PoE on SF-300-24P to AIR-AP1231G

Hi,I have a problem with switch SF-300-24P and AIR-AP1231G-E-K9.The AP is working fine in a switch 2960 or 3560, and I want to move it to a new SF-300-24P.When it is plugged in SF-300, the AP never get boot up , it obtains power, and blinks its leds,...

Resolved! SG300-52 ACL help need

Hello,I am using SG300-52 switch I need to know can I block some sites for specific IP / MAC through this switch?Please help me if someone can do it.

Resolved! Radius on SF200-24

Just got a SF200-24 (SLM224GT) in to configure for a small office. According to the product manual and the web gui it should support RADIUS authentication. The switch is running the latest firmware 1.3.5.58. Full logging including debug is enabled.Ra...

Resolved! Cant get the Vlan's on internet..

HiCan anyone help me to setup this network..... i cant get the VLAN 50 and 100 to access internet, i is it any wizard for dummies anywere? I put in a drawing of my network.. pls ask if its anyting info/settings i need to check..Thx anyway

cannot update bootloader via tftp, why?????

I'm using tftpd64 to try to update the bootcode, I keep getting an error from the switch that the tftp server is unreachable and no explanation why this is happening...I'm using my computer's wired IP and the full filename, sx300_boot-13506.rfb, a...

Create graphs from the stacking ports utilization?

We have 4x sg500X-48 switch now and we are still not sure to use the stacking option or not.Today we run MRTG to read with SNMP the switch stack but I can't find the stacking ports. Also in the webinterface I can't find the stacking ports to see util...

SG300-10mp Fibre Link aggregation

Hi,I have 2 SG300-10mp switches which i am trying to create a link redundancy for over the two fibre ports.On the web interface when i go into the LAG settings ports g9 and g10 which are the fibre ones don't show up.How do i create the link aggrega...

connecting switches together

hi,What is the best way to connect switch together (with 2960 switch)..cross or stright cable...up/down or normal port ?WAN ----Router 1 --- -SW1 ---- SW2 | | ...

How to setup failover between Switches

Have a SLM2024 Switch that I need to connect to 2 HP Switches. The HP Switches have a trunk between themselves and can communicate fine. They are not stacked switches.I want to setup a network connection to each HP Switch, but do not want to create ...

Setup VLAN

Hello,I want to setup VLAN to separate attached devices (will use a VLAN capabel WLAN accesspoint).I am looking at the Cisco Small business products.Like this: SG200-08PThis is my goal:3 VLAN's: Internal, External, GuestDevices connected to Internal ...

Resolved! How to set SG200-08P to factory default settings

We need to "reset" a SG200-08P switch back to the factory default settings and noted the "Quick Start Guide" implies the "Reset" button next to the power button doesn't exist and refers the user to the "Cisco Small Business Smart Switch Administratio...

SG500 LAG over multiple switches

Hello, does SG500 support LAG with ports on multiple switches? I would like to stack a pair of SG500 and connect each client to both using LACP in order to achieve switch redundancy.

SG series switch smart port macro issues

Hi there,There seems to be a problem with some switches that it doesn't allow us to change the untagged VLAN in the smartport macro.This causes a problem: if we change it manually when we apply the smartport it works fine but if the switch reboots th...

Cisco Sg200-26P

Hi all,I have recently received a SG200-26P poe switch to potentially upgrade the office switch.So on first boot - it went through its post, got a solid green light.I then connected my PC to the first port to try and configure it via the web interfac...

Switches - Small Business

Forum Posts