I have done Stackwise virtual many times with 9500's & 9400's but they were always out of the box. The customer have 2 existing 9407R and would now like to virtualize them. I understand the priority and renumber commands to control which switch is ...
Forum Posts
Resolved! Why i can't PING the SVI of VLAN 20?
Dears, I have created a small lab using my real gear to configure an intervlan routing , i can ping my gateway but i can't ping the svi of the other vlan , also i get reply from 10.1.1.5 which is ip out of both subnets , from where did this IP came f...
Hi All, I am using a Cisco 3560 Switch and I have observed that "show clock" displays the correct time as mine but when I check logs, it shows the time 5 Hours behind me. It can be considered as the switch is showing time related to GMT timezone as w...
Hi Team, my C3750 Switch restarted Twice today and i am not sure what caused the issue. i checked my Power Supply but did not find any issue. can somebody help me to figure it out the Root cause of the issue. show versionCisco IOS Software, C3750E So...
If we have a switch that has the following vlans 10-Data20-Vlan192 -Management Let say we are ssh connected to this Layer 2 switch using the management vlan 192.168.0.2 and we try to ping a server on the 10.10.10.50 address. Does the ping from within...
Resolved! UDLD
Hi, Studying about Cisco Switching now a days and spending most of the time to dive into new Switching topic. well, i already ended up UDLD(unidirectional link detection) but this question again screwed me..!! Which statement is true when UDLD is co...
Edited For explanation:Hi , We were trying to integrate two entity having different Core switches at both sites. Demo Network Diagram Attached.The vlans for site A is as vlan 10,20,30 with intervlan routing enabled and have there default route to int...
MY setup is as follows:Router:ASUS 4G-AC53USwitch:cisco 2950Software Version: 12.1(22)EA13Cable: straight,CAT 5E, length 10meters The router has gigabit ports so that is not the problem,I have run the cable from the router to gig0/2. The issue is tha...
what dose this message mean in the 897 router logs
Hi,Recently we have installed C3650 Switch (Model: WS-C3650-24TD, IOS: 16.9.3a).We have activated smart licensing as per the following steps (https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3650/software/release/16-9/configuration_guide/sy...
Hi, The switch 9497 is locked and neither console nor ssh possible. I tried to recover the password by pulling out a passive supervisor and interrupting the booting process by pressing ctr+c but it does not enter to ROMMON mode. Any ideas will b...
Resolved! SG350 CLI
Hi,I rencently bought a Cisco SG350-10 because I just started to learn switching and routing with Cisco.But the commands I have to use with this switch are a bit "strange" (the author uses a Cisco 2960 in his book).Is this the future for Cisco switch...
Hello,I want to implement nic bonding on linux server in redundant network topology. I have diagram below of what it would look like. Both interfaces of the linux server fa0 and fa1 would be in one bond with mode active-backup, so only one of the lin...
Wow, been while since I have looked at Cisco switches. I need an affordable L3 switch that will support VRF's and static routing between VRF's. I don't need POE, 10G, 40G, 48 ports. 12 port's would be enough 24 if I must. Best I can tell the 550X w...
Hi, I recently bought a Cisco SG350-10P Switch.I now plan to add a second switch to connect 2x 10G servers and a 10G management PC.I am looking at the SG350X-24P switch.Can I use the 2x 10G RJ45 ports and the 1x SFP+ port (with a copper 10G transceiv...
