Buy or Renew
Buy or Renew

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

Resolved! Port security reporting

Are there any CLI reporting one can generate off a 3850 switch to show all the switch ports that have port-security enabled besides doing the sh run command. Also any command that could pipe a report a txt showing all the switch ports that are admin ...

johnny_5 by • Level 1
  • 1202 Views
  • 2 replies
  • 0 Helpful votes

2960x flexstacks general trend in average response times increasing, what could be causing this? any loops on the server hosts are due to round robin config on the host.

Any ideas what could be causing the response times to go up the POE switch has only been installed 6 weeks ago and it seems we are having slowness on the network. We have a VMhost which is flapping but this is the only one left the other storage devi...

IOS Upgrade

I have 3560 switch, I uploaded the latest ios version to the switch and when I reload I get this message "Error loading "c3560e-universalk9-mz.152-4.E8.bin"" and it reload itself again. Is there any solution to fix this issue?

ahmed225@ by • Level 1
  • 854 Views
  • 3 replies
  • 0 Helpful votes

Stackwise 9500 lost configuration

We have a pair of Cisco 9500's utilizing stackwise.  We recently lost connectivity to one of the pair and when consoling into it I see it just says Switch# .  I'm new to Stackwise, to reconfig do I just need to power cycle it and the active superviso...

cmparish5 by • Level 1
  • 950 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Adding MDS devices into Prime - MDS 9132

Has anyone tried to add MDS switches into Prime? We currently run Prime 3.1 and just finished installing our new MDS 9132 switches. When I added them into Prime I get an unsupported device under device type but go get completed status for last invent...

bberry by • Level 1
  • 1541 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Migrating cores, trying to get first uplink of a port in a port channel to forward faster than standard spanning tree.

I am migrating from an Avaya dual core pair to a Cisco Dual core. Have an uplink port on each switch, both in same port channel. (Switches running VSS). My challenge is to cutover the first port I plug in takes the standard 45 seconds before forwardi...

pcweber by • Level 1
  • 1013 Views
  • 3 replies
  • 0 Helpful votes

VOice port and Data POrt

Hi All,      Is it possible to configure a port as Voice port and data for users to access can u share me the switch config for voice and data port configuration to assign in workstation - users 

Yasmeen by • Level 1
  • 2948 Views
  • 5 replies
  • 0 Helpful votes

Is the Q-BRIDGE MIB supported on a Catalyst 3650 Series Switch running IOS Denali 16.3.6?

Is the Q-BRIDGE MIB supported on the Catalyst 3650 running IOS Denali 16.3.6? I don't see it via an snmpwalk and I also don't see it on the Cisco MIB locator page.  I found this site with supported MIBs for the 3650 but I am  not sure if it is 100% a...

Resolved! upgrading 4500x switches running vss

Hi AllWe currently have some 4500x switches running VSS, they are running version 03.06.05, we want to move to version 03.08.08Can we move straight to this version with no issues?Also is it a case of just copying this bin file to both switches then j...

Load more