Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Resolved! Medium Campus Lan Design Questiosn
Hi All, I've got a few design questions for a medium campus involving 3 buildings. I've got a 10g fiber connection between all the buildings. For equipment I've got an ASA 5525, Two Cat 3850's , and six 2960-X's. First question is around the ...
Resolved! Loopback Problems
I am try to setup a couple of Loopback address on my Cisco 2851 Router.... Here are parts of my config file: interface GigabitEthernet0/0 description INSIDE ip address 192.168.0.50 255.255.255.0 ip access-group 100 in no ip redirects no ip unreacha...
Resolved! service police on interface VLAN
Hi all, Any way to enable service police in Cisco 3850 on interface VLAN? Thanks in advance
Hello, I have a C3650 switch (call it switch A), it connects to another C3650 (switch B)which is configured as layer 3 with ospf on it. Switch A connects to 3 layer 2 4500 switches, nothing else is configured on this switch A except for loopback addr...
I am trying to boot the image from usb. But i am getting following error. Please help. switch: boot usbflash0:cat3k_caa-universalk9.SPA.03.06.06.E.152-2.E6.bin Reading full image into memory...............................................................
Resolved! 10 gig modules in a WS-C3750X-48P stack
Hi! I was wondering if in the same stack of 2 swites, if you could have 2 switches with different module type: Exemple: In switch unit 1 I would have a 4 port SFP 1gig module and in switch unit 2, a Tengig SFP 4 port module. So, is this possible?...
Resolved! 4507 went to romon during IOS upgrade
Hi all,I copied new ios image to 4507 .changed the boot system bootflash to new ios.changed the config reg to 0x2102.did reboot now thisconfig-register = 0x2102Autobooting using BOOT variable specified file.....Current BOOT file is...
Hi Two Nexus7K have configured with hsrp with its address 10.1.1.1 and 10.1.1.2 respectively. The vlan address for this hsrp is 101.1.3 After traceroute, i noticed the traffic goes through 10.1.1.1 instead of 10.1.1.3 Do you think this would have any...
Hi, while trying to troubleshoot a mac move, I have run the following command to see if i could get some information about this mac moves: N7K01-CPDA-CORE1# sh system internal l2fm l2dbg macdb address 5cb9.01eb.d747 vlan 100 Legend ------ Db: 0-MACD...
Hi, Marking traffic from source. E.g. VTC with DSCP Value. VTC connects into Switch. Switch has not been enabled for QoS (qos mls has not been enabled).Will the switch just pass through the traffic with DSCP value or with the switch overwrite the ...
I upgraded my 3850 switch from IOS-XE 3.07 to 16.02 and now dot1x is failing. PC connected to Cisco IP Phone, which in turn is connected to 3850. After the upgrade my phones are stuck as the "registration" screen and this is the error in my log. Need...
Resolved! Log Messages
Hi All, I'm receiving two log messages relating to Port Security that I've never seen before. I hope some of you can shed some light on the meaning. Thanks! 000125: Feb 5 08:54:09.359 EST: PSECURE: Assert failure: psecure_sb->info.num_addrs <= ...
Resolved! QOS - Marking Queuing
Just want clarification on the end result of this setup. Thanks Scenario:Traffic being Marked with DSCP on ingress. My Egress Queue is FIFOShaper Only being used by ISP on Egress out to WAN to restrict to 95 Mbps Traffic FlowSITE1: LAN---->My Rou...
Hi everyone, I would like to buy two Cisco 6509 E switches and enable the VSS on them so i can use them both as one switch for redundancy purposes. my question is what types of SUP i should order and what are there PIDs and also my other question is ...
I need to implement wccp configuration on Nexus 3K. I can find only below link about wccp. According to below link, I understand that wccp is not only supported in the tunnel interface. I understand that, other interface( like that, SVI or routed i...
