Cisco IOS Software, 7200 Software (C7200-ADVIPSERVICESK9-M), Version 15.2(4)S5, RELEASE SOFTWARE (fc1)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2014 by Cisco Systems, Inc.Compiled Thu 20-Feb-14 06:51 by prod_rel_team ...
Forum Posts
Hi,Could you help me please - I can't find correct OID for my problem. I want to get Online Diag Status via SNMP for each module from my Cisco 6509. Thanks in advance.
Resolved! Vlans and Default G/W
I have a question regarding a design. There is a switch A, Core....which has vlans only as Layer 3 Interfaces. Interface IP-Address OK? Method Status ProtocolVlan1 unassigned YES TFTP administratively down down ...
Resolved! IOS mismatch in boot and show ver
Hi, I have a WS-C3750V2-48PS-S But here is the problem i am facing, when i do a show version on the device is see a different IOS than what i see in boot. USER_SW1#show ver | in image|SW|BootROM: Bootstrap program is C3750 boot loaderBOOTLDR:...
Hello, I have a 1841 without flash or completely damaged flash. How I program the router in ROMMON in order that it automatically boots from TFTP without doing manually with the command tftpdnld -r?
I have a nexus 6001 with system version 7.1(3)N1(1), I want to span one source interface to multiple destination port (one sandbox, one sniffer)in same switch, does it support ?
Resolved! EIGRP Query process
Hello, As we know that if there is a route which is not FS then it is still kept in the topology table. In case when Successor or Feasible Successor are lost , then router performs a query process to identify if routes are still available. My questio...
Hi Friends, I will keep it short and to the point: I am not a QoS expert so I used Auto-QoS on my network and that break my Port-Channels. I am using Cisco 4507 with Cisco 3010. Cisco 4507: CISCO4507#show run inter gi2/7Building configuration... Cu...
Hi! I need your help in order to know if the design which I am attaching will work or I will have some problems with that. Thanks!
Hello everyone, The sysadmin at work requested my help to revamp the company's network. However, I do not have an IT role in the company but I'm currently attending a networking course at university and will be having my CCENT exam in a few weeks. ...
Dear All, our Catalyst 2960X was MAC flooded by an Apple USB-C Hub with randomized MAC addresses. Have you ever observed a similar behavior in connection with Apple USB-C Hubs ? Port-Security brought the MAC flooding to a halt. Within a few seconds t...
Resolved! Conflicting VLANs on Catalyst switch
I have a very old switch, a WS-C2950C-24. I've tried IOS both C2950-I6K2L2Q4-M, Version 12.1(22)EA7 (what I got it with) and EA14 (the most recent one I could dig up on the fora, since Cisco no longer offers this download). I've tried flashing via xm...
On an RV345P the firewall blocks the return from static routes, on an RV320 it works perfectly. I have a route from 192.168.12.x to 192.168.132.0 with gateway 192.168.12.12. The ping returns well and the route is perfect, but it does not return the c...
Hi everyone, could anyone help me? Previously we had a stack of switches with 4 (3750x) but we migrated the function to cisco nexus and we unpacked that stack using the switches individually.But every switch even unconfiguring the power-stack is aler...
Resolved! Nexus 5k ACL DHCP issue.
Trying to Configure an ACL for one of our Fex. More specifically I want to create an ACL that allows the only VLAN on the Fex to our two DHCP servers. Nexus 5k system image file is: bootflash:///n6000-uk9.7.3.2.N1.1.bin The below config ...
