Hi,I admit upfront that I'm not a Cisco guy. But I need to document our switch and which VLANs that are assigned each physical port.Something like this:CS01#show vlans all-portsPORT VLAN-------- ------Gi1/0/3 2,40Gi1/0/4 2Gi1/0/5 ...
Forum Posts
Hi All, I have a Cisco switch C9300-48T which is running at old version fuji -16.9.3 and would like to upgrade to Bengaluru - 17.6.5. However, can I check if i could upgrade directly from Fuji 16.9.3 to Bengaluru - 17.6.5? I checked under Rommon vers...
Hi, I have a Cisco C9300-48T and i would like to check the image license whether it has IPservices or IPbase or Lanbase. However when i show license all, it shows status Eval expired for DNA Essentials and Network essentials. How do i check if it has...
Resolved! Cisco switch chosen.
I require a Cisco switch model with 24 ports. 8 ports are 1G and 12 ports are 10G.
Cisco Managed Switches for Ethernet/IP & Modbus TCP/IP protocols in a Ring Topology Ethernet Network
What are the equivalent Cisco Switches for the Stratix 5700 Switches?With the Cisco Managed Switches (Layer 2), Ethernet Protocols (Modbus TCP/IP & Ethernet/IP) can be in the same network and in a ring topology without problems?Please, refer to the a...
Hello Guys, We are facing latencies on our LAN. we have a WS-C3750X-48PF-S switch with poe and phones in it. I would like to test the cables by cable-diagnostics tdr. SW-FRPAU-X00I1B-AUSR#sh cable-diagnostics tdr interface Gi1/0/11TDR test last run ...
Resolved! RSPAN Not an option on 2960-s
I am trying to configure vlan 900 as a remote span VLAN on a 2960-s following this guide. However, I don't seem to have the option for a VLAN. See the below imageI am not sure what I am doing wrong. Just some background. I had firmware 15.2.2 on this...
I am quite new to cisco packet tracer and I am designing a large network but the UI is very limited and very small and I am running out of place to add devices.I have tried clustering but is there a way to increase the size of the canvas I am workin...
Greetings to all!With not much prior experience, I landed upon looking into quite a few, legacy, spatially dispersed CISCO Catalyst 1900 Series Switches mostly with 12 ports + AX-BX ports. These were installed some 20+ years ago at my organization...
Advanced thanks for all insight.I'm working on a network with a Nexus 93108 at the core (Just found out about this) and numerous Catalyst 9300Ls on the access layer. I'm interested in deploying Trustsec, but am in need of a little clarification.1. Wo...
Actualmente tenemos un problema de excess defer frames, revise informacion Cisco respecto a esta issue e indica que la siguiente configuración, ayuda a optimizar los búferes: qos queue-softmax-multiplier 1200 Mi duda es el valor 1200 puede variar ent...
Hello,been getting a message that says NATIVE VLAN MISMATCH discovered on SWITCH B GI1/0/46 (207). , with Switch A Gi0/3 (1). so i see switch A has a trunk on port 3 allowing 1-207,209-769,772-4094and switch B has vlan 207 on port 46. If vlan 2
Hello!I hope someone with better understanding is able to help me with this problem we have.We want to be fully 802.1x compliant on all switches, and the last thing we need is for Macros to work on interfaces with multiple MAC addresses behind (like ...
I am unable to get WAN access to devices connected to a Catalyst 3650.I have 4 VLANs with 10.10.10.1-10.10.40.1 ips and inter-vlan routing is operation for LAN connectivity, but no WAN access.my licenses are belowipservices 1.1ipservices eval 1.1ipba...
