Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

I have a wan between 2 sites, one site has a 3750 facing the wan and the other side has a router, both cisco of courseThey both have a layer3 interface within the same segmet and i can ping across.the router's interface has 100\full hard coded and th...

Resolved! Trunking Question

Quick Trunk questions. It doesn't matter what the Access mode VLAN is if the port is trunking, correct?Thanks, Pat.NCR19#sh int g0/17 swName: Gi0/17Switchport: EnabledAdministrative Mode: trunkOperational Mode: trunkAdministrative Trunking Encapsulat...

Hello,I have a Nexsus 5548 that I'm trying to configure telnet access on, so I can remotely configure it.  IOS is different in Nexsus, so I assigned a managment IP address to the MGMT port and I'm able to ping the IP from other switches, but when I t...

Resolved! Catalyst 2950

hi ,i have Catalyst 2950 24 port switch and i am trying to run it in my store. i have breif knowledge of configuring cisco swtiches but google was/ is my friend and i was able to reset and factory default the switch to the original state.Now i have 2...

Hello-BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.1(14r)EA1a, RELEASE SOFTWARE (fc1)System image file is "flash:c3750-ipbase-mz.122-25.SEB4/c3750-ipbase-mz.122-25.SEB4.bin"Can't get SNMP working on 3750:snmp-server community public ROWhen t...

Hi,I'm a bit confused with the output of traceroute and ping on our Core switch. There is a printer on our network that is not always reachable. Sometimes we can ping it and sometimes we can't. It seems that we can always ping it from a device on the...

Hi allI have an issue with a 1921 adsl router I was running IOS 15.0(m5). I have upgraded to 15.1.4(m)the problem is the ADSL wont sync with a BT lineThe Firmware I have used is 4.0.15  and I upgraded the firmware to 4.0.17 and the line will still no...

I currently have a 3750 stack running  12.2(50)SE            C3750-IPBASEK9-MI need to add another swtich to the stack the switch is a 3750X. Since I can't use the same code won't I have a version mismatch when I incert the new switch since the 3750X...

6tgreene by Level 1
  • 591 Views
  • 4 replies
  • 0 Helpful votes

I am a newbie in networking. I have two network and would like to allow 1 pc on another network to print to a printer on a another. Below is my description.Network 1:192.168.13.0/255.255.255.0192.168.13.125 -> xp desktop192.168.13.1 -> gatewaygoal: t...

hugh_vagn by Level 1
  • 1827 Views
  • 8 replies
  • 0 Helpful votes

I'm going to replace an MRV switching infrastructure (built on MRV MR2228-2C, MR2326, MR2324 and other) with a cisco infrastructure built on Catalyst (based may be on cat.3750X and cat.3560X) and I need a detailed competitive guide between MRV and CI...

Resolved! Nexus 5000 vs SPAN

Hi all,We are looking to change our small data center catalyst switches for a setup of Nexus 5000/2248. We are using SPAN for our IDS and for several other appliance. Now I'm reading the Nexus documentation (maybe old one) and I see I can only have T...

Vinny by Level 1
  • 1082 Views
  • 3 replies
  • 0 Helpful votes

I have a client that has two stacks of 3750X switches as well as a mixed stack of 3750's and 3750X's.  On the stacks that are just 3750X's, none of the link lights work when the mode is set to status.  However, when you do a show int status, the swit...

deyster94 by Level 5
  • 8726 Views
  • 12 replies
  • 0 Helpful votes