Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...

Resolved! C2960S QoS

Hi ExpertsI want to classify traffic by using class-maps in a Catalyst C2960S but it doesn't work (class-maps doesn´t match any traffic)RH0A01-SW1#show policy-map interface GigabitEthernet1/0/34 GigabitEthernet1/0/34  Service-policy input: QoS_Standa...

Hi,We are facing this error in our 6506 switch when we insert the second sup2.We can see a hardware version mismatch between both primary and secondary supervisors. Other parameters are matching. /* Style Definitions */ table.MsoNormalTable {mso-...

gururajan by Level 1
  • 612 Views
  • 1 replies
  • 0 Helpful votes

Resolved! ACL question

ACL's are my weak spot, I don't do many so it has not sunk in like it should.My question is, when I do a "show access-lists" and I see (23 Matches) does that mean since the reboot there have been 23 packets that matched that ACL? And if I do not see ...

burleyman by Level 8
  • 700 Views
  • 3 replies
  • 0 Helpful votes

hi,getting error while try to copy run conf to tftp in 3750 switch other devices don't have issues only this model facing the error(tftp server ip pinging no firewall on pc )Please helpme anyone

I have connected a new switch in my office last week that is Cisco 2960  TCL. But I didnt configured the switch yet but its connected and working  fine. The switch took an IP address from my DHCP server. Now I want to  configure the switch. But I can...

Because a picture tells more than a thousand words; herewith a part of our network topology (IP’s are not valid, just an example) The picture is how the network is configured currently, except for the VPN tunnel.How is works currently the Remote Offi...

emartens by Level 1
  • 3210 Views
  • 11 replies
  • 0 Helpful votes

Alrighty so I guess I'll lay it all out here and hope for some answers.I just got a brand new cisco 891 to replace our main router at work here. It looks pretty but it wont do much routing. The switch works fine and I can do the basic networking task...

Hi,I have a 3750 stack that connects to a 3560 at another site.  The are both on the inside of our network and basically a switch to switch connection.  The switchports are in vlan 901.  When I telnet from the 3750 to the 3560 and attempt to change t...

LEN SNEED by Level 1
  • 8309 Views
  • 18 replies
  • 0 Helpful votes

Hi,I have a cisco WS-C3560G-24TS layer 3 switch in my network where I have done vlan and some static routes. Current IOS in the switch is Cisco IOS Software, C3560 Software (C3560-IPBASE-M), Version 12.2(35)SE5. It seems this IOS doesn't support Poli...

Hello,We just received (2) 7018 Nexus switches. We are looking to use these switches in the distribution layer with connectivity down to our layer 2 edge switches.  So it's not going to be used for DC.My questions are what type of First-Hop Redundanc...

latintrpt by Level 1
  • 1938 Views
  • 10 replies
  • 0 Helpful votes

When attempting to configure the internal access point (wireless)  of our 881W via Cisco Configuration Professional v2.3, Interface Management | Wireless we are asked from a username and password.We have entered the admin username and password that w...