Running "show ip pim config-sanity" reports the following error for an RP that I've configured but I cannot see whats causing the error. PIM Configuration check to catch any obvious errors in vrf default Finding local Static RPs PIM config errors......
Forum Posts
I am having cisco 9407R with dual supervisor mode. Last update i did with issu upgrade.. Now i would like to downgrade the IOS, but i am unable to do it.Current version: 17.6.1Target version: 17.3.4As rollback is not possible, Kindly let me know alte...
Hi Team, Can you please provied the CFM and ERPS configuration for below CISCO NCS540 device. RP/0/RP0/CPU0:CISCO-NCS#show versionWed Oct 12 13:45:42.704 ISTCisco IOS XR Software, Version 7.1.2Copyright (c) 2013-2020 by Cisco Systems, Inc.Build Infor...
Hi,I am new to networking. I have questions on syslog severity. Now below is the chart that i got from cisco website.Q1> If I chose to send severity 6 logs then will it send informational logs along with it's 0-5 severity logs to syslog server?? Or o...
Resolved! switch ACL behaving stateful
Below is my ACL, applied to the interface inbound. Catalyst 2960CX. The first line was intented to allow DHCP. The second is intended to create host isolation. The host connected on this interface has an IP that is part of the network described in li...
Resolved! High CPU Utilization on Catalyst 3850
Hi all, I have a stack of 4 Catalyst 3850-24X working as a distribution switch, lying in between a Nexus 7K core switch and 34 C3850 access switches/stacks. I was struggling with high CPU utilization problems happening on the distribution switch. I u...
Do I just patch each of the 10G breakout cables to the remote switch I want to connect to as show below.
Hello,I'm looking for a pinout of the control pins for the NXA-PDC-930W-PE power supply. I've tried providing the unit with 48V input power, but the output doesn't turn on. I assume that one of the control pins needs to shorted or tied high/low. The...
Resolved! ASA drops sftp connections
Hi,We have a site to site vpn between our cisco firewall and Google cloud.10.10.0.4 is on Google cloud10.0.1.215 is behind our firewall.10.10.0.4 can ping and ssh to 10.0.1.215 well.On 10.10.0.4, there is a sftp client to pull data from 10.0.1.215 se...
I'm getting ready to replace some old EOL 2960 and 3560 8 port switches. I'm looking at going with 3560CX or C9200CX 12 port switches. PoE doesn't matter. What are peoples experience with the 3560CX and C9200CX switches? What are pros and cons for th...
I have a network of several PCs whose routing is done using a Cisco 3650 switch. I want to use Cisco Jabber for making calls between 2 PCs. The PCs are configured on Vlan 54 and Cisco Jabber is set on Vlan 60. Each time I want to use Cisco Jabber bet...
Sometime in the past 4-5 months we have developed a scenario that spikes the CPU enough that the console is unresponsive and packet forwarding is impacted for 6-10 seconds, etc. We can recreate it at will. It is always when the first port in a port c...
Resolved! Cisco 9300 UXM port issue
Hi all,We are having some new 9300 UXM in production replacing the 3850s, and meet a strange issue.There are some old POE devices running well on 3850. But with the new 9300UXM, we can see the port POE status is up, however the port status shows "not...
Resolved! Show Exact Temperature Value on 2960-G
Hi Guys, Is it possible to show the exact temperature value on 2960-G? When I issued command "show env temperature", the switch only displayed information below: SW2960G#sh env temperatureTEMPERATURE is OK But on my other switch, when I issued th...
Hello everyone, we are having issues with a Catalyst 6880-X-LE switch which constantly shows a CPU usage of over 90% in idle, during business hours the switch is crashing. The software installed is 15.5.(1)SY8. The command "show proc cpu sorted" tell...
