Switching

Hi All CCIE'S and cisco champions...It's a basic question about IP but i don't know it and i am eager to know it..........Please help me out.....I have some data to share with you and then i have some confusions that i like to ask.I captured the pack...

I have 2610XM. I have configured register value to 0x101 for bext reload into RxBoot mode(Mini IOS), but it did'nt work on 2610XM, it work successfully on Cisco 2522, Why this, Is there any other register value for 2610XM to boot into RxBoot mode.Ple...

I posted this in the VPN Section some days ago. Maybe anyone here can help?We are terminating an VPN (for CISCO VPN Client) on PIX515.The Adresspool for the VPN is part of the ethernet1 (inside) pool and is not translated "nat (inside) 0 ...". The in...

Hi,I was able to borrow a 2610 that has 1 Ethernet, 1 aux and 1 serial port. I want to practice routing on the two interfaces -- serial and Ethernet and I want to do this at home. The ethernet side is easy but what cable and/or special configura...

Hi..We use cisco 2950 switches in several locations at our campus. All of them are locked up in cabinets. Some of these cabinets are located 2 to 3 meters away from clerks and receptionists working in an old building with no rooms designed to enclose...

Hi,Its a basic think but pls help me out..As per the theorey...layer 2 switch performs the three fuctions mainly, learning forwarding and loop avoidance.In a multilayer switch we can put the ACL and implement the QOS features.I am surprised, that we ...

Hi Guys,i have just setup 2 routers point-to-point with DB60 back-to-back cable.Routers is configured with only ip addresses.RouterA is able to self-ping and the next-hop(RouterB).RouterB is only able to ping to next-hop (RouterA) BUT not self-ping.A...

Greetings,I am looking to set up a little lab and what I want to do is be able to use the Cisco CallManager 4.0 software and be able to configure a 7960 IP Phone. What problem I am running into is finding out exactly what I need to do this. I do not ...

We are NATing the outside source address of the serverA.Our configuration:ServerA (172.23.1.5/24)RouterA (Eth0- 172.23.1.1/24, S0- 172.16.3.2/30)RouterB (S0- 172.16.3.1/30, Eth0- 192.168.27.2/29)Firewall ServerB (198.203.239.66)We can ping and tracer...

Does anybody happen to know if IPX packets can be NATed the same way IP packets are. If not, what is the alternative to NAT the ipx traffic?thanks.

A very simple setup: a 2600 router, with one interface patched into a 2950 switch and the other interface patched into a 3550 switch. Both switches have vlan1 as their management vlan. We have defined vlan2 on both switches and configured a couple of...

I need to filter WWW traffic via ACL on my 2950. What I would like to do is say deny all WWW traffic accept for my intranet site. I can't seem to get passed the sequence of commands. Any suggestions? Vlad

We've had a few instances where development testing in our lab has caused the entire network to be compromised. I'd like to keep this from happening, but I'm trying to get some ideas besides my own. I have attempted other solutions in the past, but...

I am a graduate student and work part-time for a financial services company. The company I work for is headquartered on the West Coast and will be opening an office on the East Coast by July 1.It is my responsibility to achieve a cost-efficient netwo...

Hello *I'm slightly confused about our new PIX 515. The device must response to three outside IP-Adresses (three different ipsec tunnels). But I can't get to create new interfaces on ethernet0. Either they are created with VLAN ID 1 or PDM complains...