Hello, We just received our new Cisco 9600 swtiches and I tried to upgarde them the version 17.2.1. I followed the procedure from this Release Note Everything seems to work fine except from point number 5. Step 5 upgrade rom-monitor capsule golden...
Forum Posts
My configuration is as follows, indicating the native vlan on each trunk interface:the native vlans are fully tagged across these trunks (except 1003). when I connect the cisco 9300 across the wireless mesh, I get a PVST vlan mismatch error at my rou...
Hello Guys, I have a VLAN with over 200 hosts. I am trying to separate about 6 different hosts from the rest of the hosts in the same VLAN. I want host 1,2,3,4,5 and 6 to be able to communicate with each other but all other hosts from 7 to 200 to NO...
Resolved! Does Catalyst 9300 includes network essential base license once smart licensing is enabled?
Hi, I saw one catalyst 9300 switch the license status like below: smart licensing is enabled, but the device is not registered and eva license for DNA and network adv are already expired. but the switch works as normal. anyone can please help expl...
Resolved! Add another Switch, How to configure?
Hello,I'm new to the community and not much familiar with Cisco-Switches. So far we have a Cisco C3560X switch (SW1) in our network and now we get a new segment, for which a C3560G (SW2) will be used. With the SW1, 4 VLANs are configured, the routing...
Resolved! Need Hardware end of life details
Hi All, I am trying to find Hardware end of life support for Cisco products for below types, is there any way to get that information. WS-C2960S-24TD-LWS-C6509WS-C3560G-48PS-SWS-C4500X-40X-ESWS-CBS3012-IBM-IME-3800X-24FS-MME-3600X-24FS-M ASR1001-XASA...
Hi, This is Cisco 9500 Series switch stack and I am getting alarmed as "%SMART_LIC-3-RESERVE_HA_FAILURE: The license reservation information on the active and standby does not match. Licensing HA will not work properly: Reservation type in active and...
Hi everyone, I am looking for a way to monitor my switch 2960S and 2960X, i need to know if a member from a stack is down. I found a MIB for my product but i can't see the right OID for that... Can someone help me to find th right one ? Many Thanks
please recommend a good python tool with auto compeletion. i.e. if I type 1st letter of the command than i should get auto options of all commands that start with that letter. i.e. if i type "a" then i should get all command options in popup that sta...
Hi team, i'm a newbie in this area. please go easy on me :) . i have some question on how can i achieve my goal to block all connection to specific ip and at the same time allow from specific ip. The scenario that i have is, i'm having a switch confi...
Hi, I am having a problem with some new vlans I created.We are getting ready to implement a new phone system and I was working on setting up new vlans that will be used for voice. My network is hub and spoke (P2P). All switches layer 3 - 2960x I hav...
Hi, Someone might ask the same question before but I can't find it.I just want to clear/remove the VTP domain from my switches(2900/3550/4948), but can't succeed. Can anyone advise what the command to acheive it? TIA!
Resolved! MI FPGA and IO FPGA
Hi, I'm looking into what "MI FPGA" and "IO FPGA" are as it pertains to the Cisco Nexus 93180-YC switch architecture. I know that the MI FPGA is between the front panel ports and the Platform Controller Hub. From my research, I understand that the FP...
Hi,I'm finding what looks like Cisco blanket disabling the TDR (cable test) feature on switchports on the 2960-X if the downstream device is negotiated to anything other than 1000Mbps. Is this done intentionally, or am I hitting some kind of bug? Wh...
Hi folks. I am new to Cisco products and there are a few things I amtrying ot configure. I am running a 2821 Router with IOS v 12.4(10a).I am trying to configure the URL filtering portion of the firewall ACL. I have configured to deny one site, the...
