Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...
Forum Posts
Recently need to upgrade C9407 Current version: 16.12.03aTarget version: 17.9.6a Supervisor 1 XL Module with 25G FW: 16.12.2rCPLD: 19032905 Two 9407 SVL units---Can't find the upgrade path in official documentation?Can we upgrade directly from 16.12....
Hi,I am tshooting this. there is a port-channel with two physical ports configured on cisco core mode LACP active and the other side which is fortigate also configured with LACP active. was working fine and recently cisco keeps reporting one port ( s...
Hey Everyone!I accidently factory reset one of the switches and used command "factory-reset all" instead of just a config. Now I lost the software image in the flash/: and lost all the pkg files inside the flash.how I can recover the software image f...
I need to simulate some VoIP traffic, FTP traffic, and HTTP traffic at the same time in Cisco Packet Tracer, and I want to monitor the delay and jitter for these three types of communication. Is it possible to do this in Cisco Packet Tracer in any wa...
DSW1 is working as ACTIVE for VLAN 10 and 20. DSW2 is working as ACTIVE for VLAN 30 and 40. All PCs are able to ping their respective Gateway. PCs from VLAN 10 and 20 are able to ping each other. Similarly PCs from VLAN 30 and 40 are able to ping eac...
ello everyone, I'm getting falpping between port Gi1/0/16 and Gi1/0/23. Here is my config on the those interface: s16-smc-mdf-3750#sh run int gi1/0/16Building configuration...Current configuration : 206 bytes!interface GigabitEthernet1/0/16descripti...
We are experiencing an issue with a Cisco Catalyst C9300L-48P-4X where the device does not save the configuration. After running commands such as: Version:17.12.2r write memory copy running-config startup-config the configuration is n...
Hi, The performance positioning as per Cisco site is 350Mbps but somewhere the Data sheet its mentioned that the Encryption data is limited to 50Mbps by default and needs performance licence to increase the same to 250Mbps. https://www.cisco.com/c/...
Hi guys, I need a help with issue. Our customer is having 9200L as edge switches (varied models due to PoE demands), some stacked, mostly not. We are running Ansible automation and push commands every night around midnight. And there is one stack whi...
Resolved! C9200L Failed to STARTUP or BOOT
Jul 20 23:02:42.218: %BOOT-3-SYSD_SInitializing Hardware... System Bootstrap, Version 17.9.1r [FC8], RELEASE SOFTWARE (P)Compiled Sat 07/23/2022 16:14:02 by rel Current ROMMON image : PrimaryC9200L-48P-4G platform with 2097152 Kbytes of main memory b...
Resolved! SG300-28P firmware update
Hi all,I have in my hand an sg300-28p with firmware 1.3.0.62 and bootloader 1.1.0.6. I want to put it in the latest version (I'm aware of the in-between I have to do because of new bootloader version) but I don't see any firmware for my switch.There ...
I'm using the rip protocol now, is there a better alternative to OSPF? How do I write it without OSPF? router rip version 2 network 3.0.0.0 network 4.0.0.0 network 10.2.2.0 0.0.0.255 network 10.2.3.0 0.0.0.255 network 10.10.40.0 0.0.0.255 network 10....
Hi, guys. I find a problem that when I try to attach an acl on a snmp community, it returns a wrong notification, like this: I'm sure that I have been create acl 5, but it didn't work. do you have any clue? By the way, I have four communities on thi...
Hi Dears i changed my username password byusername admin password asd123 role priv-15Now when login by ssh switch donnot allow me loginHow fix thisPlease Help me
Hello everyone, I am performing an IOS upgrade on a Catalyst 2960X-48FPD-L stack and I am facing an issue with one of the members. Hardware:– Catalyst 2960X (3-member stack)– Model Revision: early revision (0)– All three members have the same IOS im...
