Hi,My Cisco Ex90 is connected to DSL home connection. I want to call to an IP Endpoint with reachable as IP like Cisco C20or EX90. I set the EX90 in H323 Setting -->NAT the Public IP of my Public IP Address and he has also an internal IP address. I c...
Labels
-
3PCC
(1) -
ASA
(1) -
Buying Recommendation
(36) -
Cisco Bugs
(1) -
Cisco Cafe
(14) -
Cisco Proximity
(1) -
Collaboration
(2) -
Collaboration Endpoints
(9) -
Collaboration Solutions
(4) -
Community Feedback Forum
(8) -
Community Ideas
(3) -
Conferencing
(1,887) -
CUCM
(2) -
Desk Endpoints
(227) -
Feature Idea
(1) -
General
(1) -
how to order
(1) -
IP Phone and Accessories
(1) -
Optical Networking
(1) -
Other
(4) -
Other Advanced Threats
(1) -
Other Collaboration Applications
(4) -
Other Collaboration Endpoints
(1,818) -
Other Collaboration Topics
(4) -
Other Network Security Topics
(1) -
Other Security Topics
(1) -
Other Switching
(1) -
other topics
(1) -
Other Unified Communications
(2) -
Other Unified Computing System
(1) -
Other Webex Topics
(3) -
Peripherals
(311) -
Platform
(1) -
Room Endpoints
(15,769) -
Security
(1) -
Security Management
(1) -
Small Business Voice and Conferencing
(2) -
SX80
(1) -
TelePresence
(4) -
UC Applications
(5) -
Unified Communications
(2) -
Unified Computing System (UCS)
(1) -
Video
(2) -
Video Conferencing
(7) -
Video Connection
(2) -
Video devices
(1) -
Video Over IP
(1) -
Voz IP
(2) -
Webcam
(1) -
Webex Control Hub
(1) -
Webex Devices
(7) -
Webex Meetings
(8) -
Webex Teams
(1) -
Webex Topics and Jabber
(1) -
Workflows
(1)
- « Previous « Previous
- Next » Next »
Forum Posts
Hello!My question is about non-crypto software (TCNC) for C20 codec and Touch, but it's different from the existing one.So, as far as I understand from the existing post "Pairing C20 with Touch", if we want to use touch 8" with C20 - we must have TC ...
One of our Customer is using a C40 Codec for Video and Content.In some Meetings he want to Switch from the Video Channel to a Second Content presentation.Is this possible or do I've to use a C60 or C90 Codec for this requirement.AlexSent from Cisco T...
Hi friends,I need your help once again!We have a new Cisco Telepresence enviroment to deploy. In this enviroment, we will have TC Endpoints (v 5.1) registered to CUCM (8.6.2). The CUCM will be integrated to VCS/VCS Expressway in order to be able to c...
We have large depolyment customer providing central VTC services (VCS/TMS/MCU/TCS/IPVCR/MOVI etc) to large mixed brand endpoint client base. Our customer does not have a say in what brand their clients select. Our customer would like to im...
I have a profile 52 dual and i am seeing excessive shiny spots where direct light falls, (people's forehead, cable on table). Are there any settings to fine tune this? I haven't made any changes to backlight, brightness, whiteness etc- all set to aut...
I couldn't seem to find it, although I fully admit I may have missed it in the install guide, I have a question about the feasibility of installing TMSXE on the same server as the TMS application.I do know that on page 9 the guide says that Cisco "re...
hello all, i have now encountered this issue 2x in 2 seperate customer environments. the promlem i am having is getting video to pass between CUCM and VCS when CUCM is on version 7.1.5. i have built a sip trunk according to the Cisco config guide (...
Hi.Two quiestions:1. All our video terminals are widescreen, and then you use MCU streaming, you get 4:3 video streamed, cut left and right borders. I did not find corresponding option in settings. Any suggestions?2. Is there ability to connect to co...
Hi ,I just wanted to know whether there are two different authentication credentials for XML- RPC call and for CLI access ?I cant get this info in docs which i have.Regards,Shankar
Hi,I've a problem using a TouchPanel paired to a C40 TC5.1 (issue also present in TC4.2) when I try to call to a contact (IP) shared by TMS (13.1).C40 is registered in a gatekeeper (gatekeeper mode), once I press over 'Call' an error appears:Cannot c...
Hi,I'm tasked with setting up a demo environment on a production client's network, we will just install 3 end points, most likelly SX20s for ease of deployment, my question is:What is the simplest and most effective scenario to deploy the units?They ...
I have a Tandberg 6000 Classic running E3.4 software, I know its very old.....We are working to get the system replaced with a C series Codec, but in the mean time we want to have the 6000 use the TMS Corp Dir phone books.We had several classics on t...
Do the C-series codec have the ability to switch camera preset based on microphone level? For example when mic 1 is receiving the strongest audio level then the preset 1 is activated, when mic 2 is the strongest then preset 2 is activated. ...
Hi eveybody,I am to a customer and I meet this error when I try to install a TMS software on a VMWARE ESX :Someone can help me plz
