Hard drive failed in a C240-M3. New disk plugged in (hot swap), but array did not automatically detect and rebuild the array to include the new drive in the same slot.Customer is asking for us to get this taken care of, but they have an intensive ch...
Forum Posts
Background:Hardware: Cisco UCSX-210C-M7BIOS Firmware Version: X210M7.4.3.5a.0.0905240935TPM: Enabled, Version 2.0 (Model: UCSX-TPM-002C)ESXi Version: VMware ESXi 8.0.3, 24022 / vCenter 8.0.3We have successfully installed ESXi in 7 servers on prem wit...
We have a USC C240 M5SX server. We recently upgraded the server from ESXi 6.5 to 8.0 u3 with the latest patches applied.The ESXi network management will not startup automatically after we upgraded to version 7.CISCO support has mentioned that the se...
Cisco UCS X410c M7 Compute Node Installation and Service Guide - Servicing the Compute Node [Cisco UCS X-Series Modular System] - CiscoWe've recently purchased the above compute node and have created service profile. We have an existing UCS environme...
Hello There, I am new to Cisco UCS technology and trying to configure Cisco UCSx9508 in our environment hence I have some question on configuri g chassis and port connectivity 1. Do I need Cisco Nexus switch to connect Fiber Interconnect ? If yes an...
We have (4) power supplies in a 5108-AC2 chassis and have made no connections to the FI as of yet. We connected all (4) supplies and all shows a 'amber' status.
Hi Guys,Yesterday we have done a hard disk replacement for the corrupted disk after replacing the new disk it is currently showing unconfigured good. may i know is it a usual behaviour or else i need to perform any tasks regarding this. Thanks.
Resolved! UCS 220M3 Auto Startup
Hello Guys,I have a problem with Cisco UCS 220M3 ,for test we cut the power off of the server and when the power is back on,the server does not start up automatically and i have to press the power button in order for it to start.Note that i have alre...
I am running Cisco UCS version 4.3.4a and have Cisco UCS C240 M7SX rack servers. I de-commissioned one of the rack servers and am trying to re-commission it and it just hangs. No progress.
Resolved! BIOS defaults and much confusion
Hey all,I’ve got a bit of a rabbit-hole query that I’m hoping someone here can help me unravel. Here’s the setup:Background:Hardware: Cisco UCSX-210C-M7BIOS Firmware Version: X210M7.4.3.5a.0.0905240935TPM: Enabled, Version 2.0 (Model: UCSX-TPM-002C)E...
Hi All,Situation : I was upgrading a 2x6296UP system with all C-series servers but during that upgrade the (inactive) FI-B died (yes these are old boxes!) => console output showed lots of 'panic' and 'dump' tracesProblem : i don't have a spare 6296U...
What is the "Admin Host Port" on UCS Manager, and How does it work on UCS(VIC, IOM, etc) architectures? "Admin Host Port" has this : 1, 2, Any And If selected "1" for vNIC, their are mapping on first of PCI address. But, selected "2" is mapping on en...
This is not so much a post looking for assistance (maybe it will turn in to that, I'm not sure). Rather I thought I'd share what I think is happening now with the VIC 1340 cards so others can avoid some headaches. It looks like Cisco made some chang...
Resolved! set boot image for UCS-FI-M-6324
I have formatted and installed new firmware on a UCS Fabric Interconnect 6324.Whenever the system is power cycled, I get the loader>prompt and have to manually issue the boot command for the kickstart image.How can I configure the system to automatic...
intersight with ucsx-210c-M7 bladesUpdated successfully all the firmware on the blades to the latest starred version 5.2(2.240053) via intersightI assumed this would update the bios the servers as well.?when I boot the servers via kvm it shows a low...
