Hi all, Probably a dumb question but I have a UCS B460 would anyone know if it's possible to configure it to work independently as 2 x UCS B260’s, I’m guessing it’s not possible without the correct terminatorAny ideas greatly appreciated
Hi all, Probably a dumb question but I have a UCS B460 would anyone know if it's possible to configure it to work independently as 2 x UCS B260’s, I’m guessing it’s not possible without the correct terminatorAny ideas greatly appreciated
Dears, I have 2 no's of Fabric Interconnect and from each FI i have 2 no's of connection to 2 no's of core switches 6509 ( in VSS) , My port channeling is not coming up,on the switch end i see the the bundle is in waiting state but from FI end i do...
has anybody seen System Software event: Processor sensor, Configuration Error was asserted. running ESXi6.5 and its was hung on a dump screen this morning, The esxi console screen what i could understand was Machine check exception: fatal MCE on...
Hi everybody,please check the below parts and explain to me the usefulness and the positioning of the ucs part numbers.brkukuPart Number Description•1. R200-BUN-2 UCS C200 M2 Rack Svr, 1xE5640, 1x4GB, 1PS•2. R200-BUN-3 UCS C200 M2 Rack Svr, 1xE5620, ...
am having an issue where my UCS server hangs on bootup at the "Configuring and testing Platform Hardware..." I have followed the necessary steps to clear the CMOS , and then update bios with CIMC , USB , TFTP and CLI , always he show me "Completed ...
Hello, I am setting up 2 6248 FI's as a new cluster. I erased configuration on both units, completed initial config on A-unit, and it is fine. I complete the initial config on B-unity, and it is able to join the cluster OK. However, when the B-Uni...
Hi, i'm really confused why would anybody configure "vNIC/vHBA Placement Policy" manually. When i setup Cisco UCS i always choose "Let System Perform Placement" Am i missing some hidden jam that i might be using manual instead ?
Hi, where can I find a Visio stencil that contains the UCS-EN140N-M2/K9? I have looked into the ones for the routers where this can be plugged-in, as well as in the UCS area. None of the stencils seems to contain this specific module. Thanks.
Hi,There are several blogs and white papers that describe how to configure QoS and Jumbo Frames. But they differ in therms of MTU size. Most official UCS based white papers configure an MTU size of 9000. What is best-practice for a FlexPod? Configure...
Hello, I am trying to install a Fusion ioMemory SX350 card into a C420-M3 running BIOS v1.5(9)a. The PCIe card works, but it's operating at the default power of 24.75W, and the documentation indicates that it can provide better performance if it can...
Trying to get UCS to boot from SAN and just running into issue after issue. Running B200-M5 blades. The profile is set up so that the CDROM is first to boot, then the primary SAN and then secondary SAN. When I launch the ESXi installer, it sees the b...
Hi, I'm just preparing for a UCS troubleshooting certification, where the Redwood and Woodside commands are good to know for troubleshooting IOM-FEX. Little bit hard to study for it, because you have to use physical equip. UCSPE is not supporting t...
Hello,I deploy actually a Stretch Hyperflex. I am blocking at the step of the creation of the cluster. Indeed, the communication between the FI6332 and the nexus 9000 doesn't work.There are port channel between N900 and FI6332, all vlan are trunk in ...
Hello everyone. I recently discovered following error in my environment (5108, 2208XP (4.0.1c), 6248UP (4.0.1c), B200M3 (3.1(25d)): Affected object : sys/chassis-1Description : Thermal condition on chassis 1 is upper-non-recoverableID...
Hi, I am getting "Login Error: Failed Login info: User reached maximum session limit" when trying to login to UCSM over web.But I managed to login to UCSm using cli. What is the command to terminate/kill the old admin sessions from cli in UCSM.Please...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-18-2025 09:21 AM | ||
05-21-2025 07:35 AM | ||
05-07-2025 03:02 AM | ||
05-07-2025 12:11 AM | ||
04-30-2025 01:15 AM |