I've an UCS C200 M2(SFF), which has 2x E5620 CPU. According to the Cisco specs the maximum CPU is X5675, however, I see online sales for the same server fitted with X5680, so I bought two of them ... However, the systems doesn't seem to recognize...
Forum Posts
I am getting this fault in UCSM. SNMP User can't be deployed. Error: AES is not enabled
HiI know we have to use fabric interconnect in FC Switch or EHM.I am in EHM now and I want to connect one storage directly to one of my servers, but for this result I have to change to FC switch mode.I want to know if it has solution so that we can c...
Hi, I can see 2 errors on one of the FC port in FI-A this morning as shown below. 792360002179 frames input, 1385887602556848 bytes0 discards, 0 errors0 CRC, 0 unknown class0 too long, 0 too short554127723180 frames output, 976389804559700 bytes0 dis...
Resolved! UCS Blade Health LED Blinking GREEN
Hi All, We have a strange situation. On one of the Blades in the UCS Chassis BLINKS the Health Led in GREEN. There is not any events in the logs. The other Blades in the chassis are ok (Green Led lights) B200 M5 Blades (Fw version: 3.2.3h) Could ...
Hello, One of our disk has a amber light on it but when I login to vSphere Client all of the disk are showing normal. Does anyone have already encounter this issue.
Hello all, Hope you can help. We have 2 Virtual drives on Raid 0(zero). We had added a new 900Gb hard drive to our UCS server. However, the current Virtual drive 0 has 2 x 300gb, so now have mixed hard drives and of course this is not allowed wit...
we are looking for ENIC and FNIC drivers for RHEL7.5 Host Firmware 3.2(3) Server Type: B-SeriesServer Model: Cisco UCS B200 M3Processor Name: Intel Xeon E5-2600 v2 Series processorsOperating System: Red HatOperating System Version: Red Hat Enterprise...
HELLO ALL i am facing problem installing ESXI ON C240 M5S THE DISKS ARE NOT PRESENT TO INSTALL ON IT HOWEVER TRIED DIFFERENT ESXI IMAGES CUSTOM AND NON CUSTOM with different versions 6.5 u1 6.5 u2 ALL FAILS please if any one faced it or have the ...
I have a UCS system setup with 6248UP fabric interconnects (2 x 6248UP connected to a chassis with 2 x 2208xp fabric extenders), running the latest 4.x release on everything, it's basically a fresh setup. Nothing fancy, uplinked to a pair of Nexus 30...
Resolved! Unable to boot UCS blade from SAN
Hello,I am a newbe to Cisco UCS systems, I am an trying to boot UCS B200 M3 blade from SAN, ESXi was installed sucessfully, boot policy is configured properly (I suppoe), but it's not booting from it, I've even re-installed ESXi again, but didn;t boo...
Resolved! HCS // MIGRATION FROM N1K TO VDS
Hi, For our architecture we need to migrate from vCenter 5.5 to 6.5, so we need to migrate from N1K to VDS, N1K is not an option. In N1K is marking L2 QoS COS according to the DSCP of the IP packets coming from the UC Apps to the virtual switches. - ...
Greetings, So we have 3 UCS that have a FC HBA card installed, but when you check the PCI Adapters tab in the CIMC, this slot appears as "Not Loaded" in the Option ROM Status Weirdly enough, when you check the BIOS Parameter configuration you see t...
Hi all, I have been thinking about using Ansible for our UCS infrastructure. After digging into the subject I am still undecisive concerning the best directory layout and how to use the already existing role (https://github.com/CiscoUcs/ansible-role-...
Hello Guys Pls Advise on the below Raid Config for SAS DisksDisk01 and Disk02 = RAID 1Disk03 = HotswapDisk04,Disk05,Disk06 =RAID 5Disk 07 = Hotswap for Raid 5 thanks all
