Here is what I have. I have a UCS mini at fw version 3.0.2C and we are going to 3.1.2C. Before starting a call to TAC to open a pre-check prior to the upgrade, I created my backups and I was going to boot each fabric interconnect separately to clear ...
Forum Posts
Hi, We have 3 blades of B200M5 Same Firmware, same Service-Profiles for 2 of them I'm able to install ESXi 6.5 on 1 of them, I'm getting an error in the start of the installation [after 1%] What can it be ? Thanks
Hello! We have 2 x UCS-FI-6248UP + 1 x Cisco UCS 5108 Chassis (7 Servers) with 2 x Nexus 5548UP Switches with L3 Modules (Data Ceter Routet Access Scheme). In UCS Manager I see FI A with state "inapplicable" and Fi B is currently "primary". Using CLI...
Hi Folks,We've been a UCS customer for about 9 months. We have been steadily replacing HP Gen6/7/8 blades with UCS B200 M3 and B200 M4 blades as well as experiencing a large amount of growth, we are at 197 M3/M4 blades at the moment, 6148 and 6196 F...
Our have configered FI to Nexus with NSX. it's mode Port-Channel mode. Asking to balacing algorithm about following mode, what is a default mode ?
Resolved! VMware Memory Sensor
Hello, we have an issue, where vmware hardware status is showing an memory error. But on my ucs manager, there is no fault, no warning or info. I have rebooted the host but the issue is still there. Any advise where this error is coming from? ...
Hi UCS Community,Has anyone run into issues whereby you're unable to discover a B series UCS chassis, IOMs or Blades.x1 5108 UCS Chassisx2 IOM 2208x4 B250 M2 Bladesx1 6120XP Fabric Interconnect.I have configured the 6120XP Fabric Interconnect as a st...
I got a b200 M5 that was in a cluster. I had to reinstall esxi 6.5 and now after reinstalling I cannot add it back into cluster. Keeps giving me this error. I have other b200M5 in this cluster and they are admitted just fine. any idea?
I am pulling out my b200 m3 in replacement of b200 m5 b200 m3 has the vic 1240 card b200m5 has the 1340 vic do i need to create new service profile for the m5? or can i take the m3 out and reassign the servie profile to the m5? also old intel...
I've an UCS C200 M2(SFF), which has 2x E5620 CPU.According to the Cisco specs the maximum CPU is X5675, however, I see online sales for the same server fitted with X5680, so I bought two of them ...However, the systems doesn't seem to recognize the C...
I need to check cisco compatibility twinax cable that I use cisco UCS C240 M5 VIC 1385 with adapter QSA CVR-QSFP-SFP10G I only see 1387 document that show below but do not see in 1385. Does anyone know? Cisco UCS Virtual Interface Card 1387 Data ...
hidoes anyone have steps on how to configure n5k for native fc to a storage controller and then map that to an interface running fcoe to a fabric interconnect say 6200 ?appreciate any pointers
I upgraded my UCS from 2.2.3g to 2.2.8i as recommended by Cisco as a requirement before going to 3.2.2d. This upgrade covered the UCS Manager, FIs, IOMs, and our Blade/C-Series servers. However, the 3.2.2d upgrade attempt failed. Adaptor unit Cis...
Hi I have an issue with a simple ucs setup ucs setup: 2 x fabric interconnects connections (same on both) port 1 & 2 - server ports to left / right 2208xp io modules port 3 & 4 - uplink to switch port 5 & 6 - set as appliance ports - connected to...
Resolved! Fabric
Can i connect FI 6332-16UP or 6248UP to direct NAS Storage ?
